Brocade Communications Systems VA-40FC Hardware Reference Manual Download Page 38 | Manualshive

Page: 38 / 60

background image

26

Brocade VA-40FC Hardware Reference Manual

53-1001540-04

Maintaining the Brocade VA-40FC

3

Field Replaceable Units (FRUs)

The power supplies have the fans inside and can be replaced onsite without the use of special
tools. The power supply/fan assembly units are keyed to ensure correct orientation during
installation. Replacement instructions are provided with all replacement units ordered.

Power supply/fan assembly FRU replacement

The Brocade VA-40FC fans are fixed inside the integrated power supply/fan FRU to provide
necessary airflow to cool the whole system. There is one fan located in the rear section of each
FRU. The system software sets fan speed and measures their speeds through the tachometer
interface.

The two power supply/fan assembly FRU units are hot-swappable if replaced one at a time. They
are identical and fit into either slot.

Fabric OS identifies the power supplies as follows (viewing the switch from the

port

side):

•

Power supply #1 is on the left

•

Power supply #2 is on the right

Determining power supply/fan replacement need

1. Use one of the following methods to determine whether a power supply requires replacement:

•

Check the power supply status LED next to the

I

/

O

switch. If the power supply status LED

is not on, verify that the power supply is on and seated and the power cord is connected to
a functioning power source. If the light does not turn green, the power supply needs to be
replaced.

•

In Web Tools, click the Power Status icon.

•

Type the psShow command at the command prompt to display power supply status as
shown below:

2. Use one of the following methods to determine whether a fan requires replacement:

•

Check the system status LED (see

on page 20 for location of system status LED).

If the system status LED is flashing amber and green, it could mean the fan has failed. The
green power supply/fan LED will also flash in the event of failure. Check the management
interface and the error log for details on the cause of status.

•

In Advanced Web Tools, check the Fan Status icon background color. It will be either yellow
or red if the fan has failed. When the fan is functioning correctly, the background color is
green.

switch:admin>

psshow

Power Supply #1 is OK
Power Supply #2 is OK

«
...
36
37
38
39
40
...
»

Summary of Contents for VA-40FC





























































Reviews:

No comments

Related manuals for VA-40FC

CRESTRON-APP-SSTV

Brand: Crestron Pages: 28

13101332 - Photoshop - Mac

Brand: Adobe Pages: 549

Brand: FARONICS Pages: 43

Brand: Allied Telesis Pages: 668

IPSEC VPN CLIENT

Brand: ZyXEL Communications Pages: 2

ENTERPRISE MEDIA SYSTEM V5.0

Brand: VBrick Systems Pages: 76

Brand: Intel Pages: 19

Brand: AMX Pages: 54

Brand: da Vinci Technologies Pages: 249

FINAL MIX VST - FOR TRACKTION

Brand: Mackie Pages: 26

NVX200 - Touch&Go - Automotive GPS Receiver

Brand: Jensen Pages: 86

CAMEDIA Master 4.3/Pro

Brand: Olympus Pages: 22

SpectraView Reference 241

Brand: NEC Pages: 68

SmartWare R.3.20

Brand: Patton electronics Pages: 573

ScanSnap Upgrade

Brand: Fujitsu Pages: 55

Neoware e370 - Thin Client

Brand: HP Pages: 24

Brand: HP Pages: 330

NonStop Pathway/iTS

Brand: HP Pages: 694

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands