manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Hardware Installation Manual

Share
Download
Brocade Communications Systems ICX 7250 Hardware Installation Manual Download Page 29

FIGURE 13 Installing the device in a two-post rack

1.

Rack-mounting screws

2. Cage nuts

6. If installing a single device only, proceed to 

Powering on the system

 on page 62. If installing multiple devices, mount them in

the rack, one above the other.

Installing the 1U, 1.5U, and 2U Universal Kit for Four Post Racks (XBR-R000295)

Use the following instructions to install a 1U, 1.5U, or 2U device in a 19-in. (48.3 cm) EIA rack using the 

1U, 1.5U, and 2U Universal Kit for

Four Post Racks (XBR-R000295)

.

The device can be installed so that the port side is either flush with the front posts or recessed with the non-port side flush with the rear
posts. A recessed position allows a more gradual bend in the fiber-optic cables connected to the device and less interference in the aisle
at the front of the rack.

NOTE
Hardware devices illustrated in these procedures are only for reference and may not depict the device you are installing into the
rack.

Installation requirements

Review the installation and facility requirements for your product before mounting the device. Refer to the hardware installation guide for
your product for more information.

Use Electronic Industries Association (EIA) standard racks. Provide space in a 19-in. (48.3 cm) EIA rack, as required for the device type,
with a minimum distance of 24 in. (609.60 mm) and a maximum distance of 32 in. (812.80 mm) between the front and back posts.

Time and items required

Allow 15 to 30 minutes to complete this procedure. Note the following requirements to ensure correct installation and operation.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

29

Summary of Contents for ICX 7250
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands