Brocade Communications Systems DCX 8510-8 Hardware Reference Manual Download Page 17

Page: 17 / 176

FIGURE 2

Nonport side of the Brocade DCX 8510-8 (sample configuration)

1. WWN bezel (logo plate - WWN card behind)
2. Power supply
3. Blower assembly

Brocade DCX 8510-8 blades

The following table summarizes the port, application, control processor, and core switch blades that are
available for the Brocade DCX 8510-8.

Blades available for the Brocade DCX 8510-8

TABLE 1

Description

Name

Function

Brocade DCX
8510-8 control
processor blade

CP8

The CP8 blade contains the control plane for the chassis. There are two CP8
blades for redundancy. This control processor blade is compatible with the
Brocade DCX 8510-8, Brocade DCX 8510-4, Brocade DCX, and Brocade
DCX-4S.

Brocade DCX 8510-8 blades

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Summary of Contents for DCX 8510-8

















































































































































































Search results

Summary of Contents for DCX 8510-8

Reviews:

Brocade Communications Systems DCX 8510-8, Hardware Reference Manual, Page: 17 / 176

Search results

Summary of Contents for DCX 8510-8

Reviews: