Brocade Communications Systems 5600 vRouter Configuration Manual Download Page 101 | Manualshive

Page: 101 / 106

background image

Supported Interface Types

The following table shows the syntax and parameters of supported interface types. Depending on the command, some of these types
may not apply.

Interface Type

Syntax

Parameters

Bridge

bridge

brx

brx: The name of a bridge group. The name ranges from br0
through br999.

Data plane

dataplane

interface-name

interface-name: The name of a data plane interface. Following are
the supported formats of the interface name:

∙

dp

xpypz—The name of a data plane interface, where

— dp

x specifies the data plane identifier (ID). Currently,

only dp0 is supported.

— p

y specifies a physical or virtual PCI slot index (for

example, p129).

— p

z specifies a port index (for example, p1). For example,

dp0p1p2, dp0p160p1, and dp0p192p1.

∙

dp

xemy —The name of a data plane interface on a LAN-

on-motherboard (LOM) device that does not have a PCI
slot, where em

y specifies an embedded network interface

number (typically, a small number). For example,
dp0em3.

∙

dp

xsy —The name of a data plane interface on a device

that is installed on a virtual PCI slot, where

xsy specifies an

embedded network interface number (typically, a small
number). For example, dp0s2.

∙

dp

xPnpypz —The name of a data plane interface on a

device that is installed on a secondary PCI bus, where P

n

specifies the bus number. You can use this format to
name data plane interfaces on large physical devices with
multiple PCI buses. For these devices, it is possible to
have network interface cards installed on different buses
with these cards having the same slot ID. The value of

n

must be an integer greater than 0. For example,
dp0P1p162p1 and dp0P2p162p1.

Data plane vif

dataplane

interface-name vif

vif-id [vlan vlan-id ]

interface-name: Refer to the preceding description.

vif-id: A virtual interface ID. The ID ranges from 1 through 4094.

vlan-id: The VLAN ID of a virtual interface. The ID ranges from 1
through 4094.

Loopback

loopback lo

or

loopback lo

n

n: The name of a loopback interface, where n ranges from 1 through
99999.

OpenVPN

openvpn

vtunx

vtunx: The identifier of an OpenVPN interface. The identifier ranges
from vtun0 through vtun

x, where x is a nonnegative integer.

Tunnel

tunnel

tunx

or

tunnel

tunx parameters

tunx: The identifier of a tunnel interface you are defining. The
identifier ranges from tun0 through tun

x, where x is a nonnegative

integer.

Brocade 5600 vRouter Firewall Configuration Guide

53-1004253-01

101

«
...
99
100
101
102
103
...
»

Summary of Contents for 5600 vRouter











































































































Reviews:

No comments

Related manuals for 5600 vRouter

Brand: PaloAlto Networks Pages: 2

Brand: Draytek Pages: 22

Brand: HotBrick Pages: 89

Brand: ZyXEL Communications Pages: 2

USG Flex Series

Brand: ZyXEL Communications Pages: 18

Brand: Watchguard Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands