manualshive.com logo in svg

Broadway Limited Paragon 3, Reference Manual

Share
Download
Broadway Limited Paragon 3 Reference Manual Download Page 144

   

144  

                        SETUP CVs 

 

CV197 
Rev Level Five Motor Load Power

 

 
 

Description

 

 

This Value Sets the Motor Load Power Rev Level Five Sound Effect 

 

Values

 

 

0-255 

 

Initial Value

 

 

180  

 

Related CVs

 

 

CV137

, CV193—CV202 

 
          

Bit 7   

 

 

 

 

 

  Bit 0 

 
          

     1        0          1          1          0          1          0          0 

 
 

The decoder’s rev level five sound effect is activated when the motor 
power exceeds this value or falls below the next rev level load power 
threshold.    Increasing  this  value  increases  the  power  needed  before 
the diesel changes to the next rev level sound effect. 

Note: This value 

must be lower than next rev level. 

 

See 

Rev Up/Down

.

 

 

Summary of Contents for Paragon 3







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands