Broadway Limited Paragon 3 Page 137 Reference Manual Download

Page: 137 / 198

137

SETUP CVs

CV190
DC Sound Setup

Description

This Value Contains Various DC Sound Setup Features

Values

0-255

Initial Value

1-7; 12

Related CVs

Bit 7

Bit 0

D7 D6 D5 D4 D3 D2 D1 D0

This value is write Only. Prior to writing this value, use the
DCMaster



and save the desired track voltage. The voltage is saved

by Muting the sounds, than Pressing AUX. The current track voltage
is saved for later storage. Writing the following

value

to CV190

indicates where the saved voltage is applied.

Value

What is saved

Destination of Saved Track Voltage

Analog Brake Release Voltage

CV192

Analog Brake Set Voltage

CV191

Shut Down Voltage

CV132

Sound Start Up Voltage

CV131

Summary of Contents for Paragon 3







































































































































































































Search results

Summary of Contents for Paragon 3

Reviews:

Related manuals for Paragon 3

Brands by name

Popular brands

Broadway Limited Paragon 3, Reference Manual

Search results

Summary of Contents for Paragon 3

Reviews:

Related manuals for Paragon 3

Brands by name

Popular brands