background image

Table 3-2. Serial EEPROM Contents 

Serial  

EEPROM 

Offset

 

Register 

Offset

 

Register Description

 

Register Bits 

Affected

 

Register 

Values 

Register Value Description

 

00h 

PCI 02h 

Device ID 

PCIIDR [31:16] 

5201 

Device ID for PCI 9052RDK-LITE 

02h 

PCI 00h 

Vendor ID 

PCIIDR [15:0] 

10B5 

PLX Vendor ID 

04h 

PCI 0Ah 

Class Code 

PCICCR [23:8] 

0680 

Other bridge type 

06h 

PCI 08h 

Class Code / Revision 

PCICCR [7:0] / 

PCIREV [7:0] 

0002 

PCIREV = current 9052 revision 

08h 

PCI 2Eh 

Subsystem ID 

PCISID [15:0] 

9050 

Default 9052 Subsystem ID 

0Ah 

PCI 2Ch 

Subsystem Vendor ID 

PCISVID [15:0] 

10B5 

PLX Subsystem Vendor ID 

0Ch PCI 

3Eh 

(Maximum Latency and Minimum Grant 

are not loadable) 

Reserved

 0 

 

0Eh PCI 

3Ch 

Interrupt Pin / 

(Interrupt Line Routing is not loadable)

PCIIPR [7:0] / 

PCIILR [7:0] 

0100 

Interrupt pin = INTA# 

10h Local 

02h 

MSW of Range for 

PCI-to-Local Address Space 0 

LAS0RR [31:16] 

FFF0 

12h Local 

00h 

LSW of Range for 

 PCI-to-Local Address Space 0 

LAS0RR [15:0] 

0000 

1MB local address space for the ISA 

Memory space access, mapped into 

PCI memory space. 

14h Local 

06h 

MSW of Range for 

PCI-to-Local Address Space 1 

LAS1RR [31:16] 

FFFF 

16h Local 

04h 

LSW of Range for 

PCI-to-Local Address Space 1 

LAS1RR [15:0] 

FFF1 

16-byte local address space for the ISA 

I/O space access, mapped into PCI I/O 

space. 

18h Local 

0Ah 

MSW of Range for 

PCI-to-Local Address Space 2 

LAS2RR [31:16] 

FFFE 

1Ah Local 

08h 

LSW of Range for 

PCI-to-Local Address Space 2 

LAS2RR [15:0] 

0000 

128KB local address space for the RDK 

memory mapped SRAM, mapped into 

PCI memory space. 

1Ch Local 

0Eh 

MSW of Range for 

PCI-to-Local Address Space 3 

LAS3RR [31:16] 

FFF0 

1Eh Local 

0Ch 

LSW of Range for 

PCI-to-Local Address Space 3 

LAS3RR [15:0] 

0000 

1MB local address space for the RDK 

memory mapped ROM, mapped into 

PCI memory space. 

20h Local 

12h 

MSW of Range for 

PCI-to-Local Expansion ROM 

EROMRR [31:16]

22h Local 

10h 

LSW of Range for 

PCI-to-Local Expansion ROM 

EROMRR [15:0] 

No Expansion ROM range set 

24h Local 

16h 

MSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 0 

LAS0BA [31:16] 

0000 

26h Local 

14h 

LSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 0 

LAS0BA [15:0] 

0001 

This space is active from local address 

0 for ISA Memory space accesses. 

28h Local 

1Ah 

MSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 1 

LAS1BA [31:16] 

0000 

2Ah Local 

18h 

LSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 1 

LAS1BA [15:0] 

0001 

This space is active from local address 

0 for ISA I/O space accesses. 

2Ch Local 

1Eh 

MSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 2 

LAS2BA [31:16] 

0100 

2Eh Local 

1Ch 

LSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 2 

LAS2BA [15:0] 

0001 

This space is active from local address 

01000000h for RDK SRAM accesses.

30h Local 

22h 

MSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 3 

LAS3BA [31:16] 

0200 

32h Local 

20h 

LSW of Local Base Address (Remap) 

for PCI-to-Local Address Space 3 

LAS3BA [15:0] 

0001 

This space is active from local address 

02000000h for RDK ROM accesses. 

34h Local 

26h 

MSW of Local Base Address (Remap) 

for PCI-to-Local Expansion ROM 

EROMBA [31:16]

0000 

36h Local 

24h 

LSW of Local Base Address (Remap) 

for PCI-to-Local Expansion ROM 

EROMBA [15:0] 

0000 

No Expansion ROM enabled – see 

EROMRR 

PCI 9052RDK-LITE Hardware Reference Manual v1.3 

© 2004 PLX Technology, Inc. All rights reserved

.

 

 

Summary of Contents for PLX PCI 9052RDK-LITE








































Reviews: