manualshive.com logo in svg

Broadcom NetXtreme BCM57 Series, User Manual

Share
Download
Broadcom NetXtreme BCM57 Series User Manual Download Page 57

Using Broadcom Advanced Control Suite 4

NetXtreme 

User Guide

 

Broadcom

®

 

April 2017 • 2CS57XX-CDUM514-R

Page 57

Managing the Host

At the host level, you can view host information and configure parameters from the following tabs:

• Information
• Configuration

To view host information

Select the host in the 

Explorer View

 pane, and then select the 

Information

 tab to view host-level information.

Information Tab: Host Information

Host Name. 

Displays the name of the host.

OS Version Info. 

Displays the operating system, including the version.

Platform. 

Displays the hardware architecture platform (for example, 32-bit or 64-bit)

To configure the host

Select the host in the 

Explorer View

 pane, and then select the 

Configuration

 tab to configure host-level 

parameters.

Summary of Contents for NetXtreme BCM57 Series















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands