background image

Troubleshooting

NetXtreme 

User Guide

 

Broadcom

®

 

April 2017 • 2CS57XX-CDUM514-R

Page 165

Testing Network Connectivity

Windows

Use the ping command to determine if the network connection is working.

1.

Verify that the drivers are loaded and enabled.

2.

Verify that the cable is attached and you have a proper link.

3.

Click 

Start

, and then click 

Run

4.

Type 

cmd

 in the 

Open

 box, and then click 

OK

5.

Type 

ipconfig /all

 to view the network connection to be tested. 

6.

Verify that the IP address is correct for the network to which the adapter(s) is connected.

7.

Type 

ping IP address

, and then press ENTER. 

The ping statistics that are displayed indicate whether the network connection is working or not.

Linux

To verify that the Ethernet interface is up and running, run 

ifconfig

 to check the status of the Ethernet interface. 

It is possible to use 

netstat -i

 to check the statistics on the Ethernet interface. Go to 

Linux Driver Software 

for 

information on

 

ifconfig

 and 

netstat

Ping an IP host on the network to verify connection has been established:

From the command line, type 

ping IP address

, and then press ENTER.

The ping statistics that are displayed indicate whether the network connection is working or not. 

Broadcom Boot Agent

Problem

: Unable to obtain network settings through DHCP using PXE.

Solution

: For proper operation make sure that the Spanning Tree Protocol (STP) is disabled or that portfast 

mode (for Cisco) is enabled on the port to which the PXE client is connected. For instance, set spantree portfast 
4/12 enable.

Note: 

When using forced link speeds, verify that both the adapter and the switch are forced to the 

same speed, or that both sides are configured for auto-negotiation.

Note: 

Network connectivity can also be tested using the 

Testing the Network

 feature in Broadcom 

Advanced Control Suite 2.

Summary of Contents for NetXtreme BCM57 Series















































































































































































Reviews: