manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

56

Section 4: System Control and Debug Unit

 Document

1250_1125-UM100CB-R

51

ldt_nmi HyperTransport 

signaled 

NMI 

This bit is reserved in the system interrupt register, and 
comes only from the 

ldt_interrupt

 register. This bit is 

set when an NMI interrupt packet directed to this CPU 
had been received from the HyperTransport bus. This 
bit is cleared using the interrupt clear register. 
HyperTransport interrupts are directed, so the source 
for this bit differs for each interrupt controller. 

52

ldt_init HyperTransport 

signaled 

INIT 

This bit is reserved in the system interrupt register, and 
comes only from the 

ldt_interrupt

 register. This bit is 

set when an INIT interrupt packet directed to this CPU 
had been received from the HyperTransport bus. This 
bit is cleared using the interrupt clear register. 
HyperTransport interrupts are directed, so the source 
for this bit differs for each interrupt controller. 

53

ldt_startup HyperTransport 

signaled 

STARTUP 

This bit is reserved in the system interrupt register, and 
comes only from the 

ldt_interrupt

 register. This bit is 

set when a STARTUP interrupt packet directed to this 
CPU had been received from the HyperTransport bus. 
This bit is cleared using the interrupt clear register. 
HyperTransport interrupts are directed, so the source 
for this bit differs for each interrupt controller. 

54

ldt_ext_int HyperTransport 

signaled 

ExtInt 

This bit is reserved in the system interrupt register, and 
comes only from the 

ldt_interrupt

 register. This bit is 

set when an ExtInt interrupt packet directed to this CPU 
had been received from the HyperTransport bus. This 
bit is cleared using the interrupt clear register. 
HyperTransport interrupts are directed, so the source 
for this bit differs for each interrupt controller. 

55

pci_error_int 

PCI error interrupt 

This bit is set when an error is seen on the PCI bus. It 
can be caused by PCI parity errors, target-abort, 
master-abort, timeout transfer abort or a serious 
system error signalled on the SERR pin. The cause can 
be read from the PCI interface configuration space 
(bus=0, dev=0, function=0) Status register (bits 8, 11, 
12, 13 and 14), and the PCI Additional Status and 
Control register. Software must clear all the error status 
bits to clear the interrupt.

56

pci_inta_int 

PCI interrupt A 

This bit is set when an interrupt is signalled on the PCI 
inta line. 

57

pci_intb_int 

PCI interrupt B 

This bit is set when an interrupt is signalled on the PCI 
intb line. 

58

pci_intc_int 

PCI interrupt C 

This bit is set when an interrupt is signalled on the PCI 
intc line. 

59

pci_intd_int 

PCI interrupt D 

This bit is set when an interrupt is signalled on the PCI 
intd line. 

60

spare_int 

Spare interrupt 

There is no system interrupt matching this bit. It can be 
used for vectored HyperTransport interrupts. 

61

mac_0_ch1_int

MAC  0  Channel  1  interrupt

Raised when channel 1 transmit or receive DMA engine 
needs service. Cleared by any read to 

mac_status1_0

.

62

mac_1_ch1_int

MAC  1  Channel  1  interrupt

Raised when channel 1 transmit or receive DMA engine 
needs service. Cleared by any read to 

mac_status1_1

.

63

mac_2_ch1_int

MAC  2  Channel  1  interrupt

Raised when channel 1 transmit or receive DMA engine 
needs service. Cleared by any read to 

mac_status1_2

.

Table 22:  Interrupt Sources

 (Cont.)

Number

Name

Description

Method to clear

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

NEC N8104-128 Installation Manual preview
N8104-128
Brand: NEC Pages: 47
Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
Idis DR-8400 Installation Manual preview
DR-8400
Brand: Idis Pages: 31
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
Tandy 26-3814 Operation Manual preview
26-3814
Brand: Tandy Pages: 24
Commell FS-A79 User Manual preview
FS-A79
Brand: Commell Pages: 36
Softing TH LINK Installation Manual preview
TH LINK
Brand: Softing Pages: 16
ZALMAN RESERATOR2 Installation And Operational Manual preview
RESERATOR2
Brand: ZALMAN Pages: 18
Procool SP480 Series Instructions preview
SP480 Series
Brand: Procool Pages: 2
Taiwan Commate Computer Inc. P2BXA-V Quick Installation preview
P2BXA-V
Brand: Taiwan Commate Computer Inc. Pages: 25
Greenlee 910FS Instruction Manual preview
910FS
Brand: Greenlee Pages: 52
Beckhoff CU8210-D001-0200 Manual preview
CU8210-D001-0200
Brand: Beckhoff Pages: 25
Lattice Semiconductor mVision AR0234 User Manual preview
mVision AR0234
Brand: Lattice Semiconductor Pages: 25
InfoStor RAID 6 Information Sheet preview
RAID 6
Brand: InfoStor Pages: 6
D-Link WCB-B11 User Manual preview
WCB-B11
Brand: D-Link Pages: 9
AMX RDC-DC/277 Schematic Diagram preview
RDC-DC/277
Brand: AMX Pages: 1
Panasonic WZ-TDDA Instructions preview
WZ-TDDA
Brand: Panasonic Pages: 4

Brands by name

Popular brands

Load more brands