manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

252

Section 8: PCI Bus and HyperTransport Fabric

 Document

1250_1125-UM100CB-R

Table 151:  HyperTransport Isochronous Ignore Mask - Offset 60Bits [31:0]

Bits

Name

Default

Description

0

reserved

R/W 1’b0

Reserved

31:1

isocMask

R/W 31’b0 This specifies the mask of bits that are ignored when the comparison is done to force

t h e i sco ch ro no u s bi t.  S ee  

S ec ti on : “ F or ce   I soc hr o no us  M od e  A dd r es s

Range” on page 212

.

Table 152:  HyperTransport Error Control Register - Offset 68 Bits [23:0]

Bits

Name

Default

Description

0

ProtFatalEn

R/W 1’b0

If this bit is set a fatal interrupt will be raised when a protocol error is detected.

1

ProtNonFatalEn

R/W 1’b0

If this bit is set a nonfatal interrupt will be raised when a protocol error is 
detected.

2

ProtSyncFloodEn

R/W  1’b0

If this bit is set a protocol error will cause SYNC flooding of the HyperTransport 
link and the LinkFail bit will be set.

3

OvfFatalEn

R/W 1’b0

If this bit is set a fatal interrupt will be raised when a receive buffer overflow is 
detected.

4

OvfNonFatalEn

R/W  1’b0

If this bit is set a nonfatal interrupt will be raised when a receive buffer overflow 
is detected.

5

OvfSyncFloodEn

R/W 1’b0

If this bit is set a receive buffer overflow will cause SYNC flooding of the 
HyperTransport link and the LinkFail bit will be set.

6

EocNxaFatalEn

R/W 1’b0

If this bit is set a fatal interrupt will be raised when a posted request to a 
nonexistent address or response that does not match a request is detected. 
(Non-posted requests will receive an NXA error in this case).

7

EocNxaNonFatalEn

R/W 1’b0

If this bit is set a nonfatal interrupt will be raised when a posted request to a 
nonexistent address or response that does not match a request is detected. 
(Non-posted requests will receive an NXA error in this case).

8

EocNxaSyncFloodEn

R/W 1’b0

If this bit is set a posted request needing an NXA or a response that does not 
match a request will cause SYNC flooding of the HyperTransport link and the 
LinkFail bit will be set.

9

CrcFatalEn

R/W 1’b0

If this bit is set a fatal interrupt will be raised when a receive CRC error is 
detected.

10

CrcNonFatalEn

R/W 1’b0

If this bit is set a nonfatal interrupt will be raised when a receive CRC error is 
detected.

11

SerrFatalEn

R/W 1’b0

The SerrEn bit in the Bridge Control register determines if an SERR will 
generate an interrupt. If this bit is set a fatal interrupt will be raised, if clear a 
nonfatal interrupt is used.

12

SrcTagFatalEn

R/W 1’b0

If this bit is set a fatal interrupt will be raised when a source tag error is 
detected.

13

SrcTagNonFatalEn

R/W 1’b0

If this bit is set a nonfatal interrupt will be raised when a source tag error is 
detected.

14

SrcTagSyncFloodEn

R/W 1’b0

If this bit is set a source tag error will cause SYNC flooding of the 
HyperTransport link and the LinkFail bit will be set.

15

MapNxaFatalEn

R/W 1’b0

If this bit is set a fatal interrupt will be raised when an NXA error response is 
sent to a request with zero source id.

16

MapNxaNonFatalEn

R/W 1’b0

If this bit is set a nonfatal interrupt will be raised when an NXA error response 
is sent to a request with zero source id.

17

MapNxaSyncFloodEn

R/W 1’b0

If this bit is set an NXA error response to a request with zero source id will 
cause SYNC flooding of the HyperTransport link and the LinkFail bit will be set.

23:18

Reserved

R/O 6’b0

Reserved

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

TC Electronic M300 Service Manual preview
M300
Brand: TC Electronic Pages: 2
GE Mini Field Agent User Manual preview
Mini Field Agent
Brand: GE Pages: 87
3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Farallon NetLINE USB User Manual preview
NetLINE USB
Brand: Farallon Pages: 26
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
B&B Electronics Parallel Printer Card PIOC User Manual preview
Parallel Printer Card PIOC
Brand: B&B Electronics Pages: 16
HARTING HAIIC MICA Hardware Development Manual preview
HAIIC MICA
Brand: HARTING Pages: 13
S&T kontron KBox E-420-R1K/V1K User Manual preview
kontron KBox E-420-R1K/V1K
Brand: S&T Pages: 82
Giacomini KPM36Y002 Manual preview
KPM36Y002
Brand: Giacomini Pages: 2
Supersonic Franky Instruction Manual preview
Franky
Brand: Supersonic Pages: 46
Caen A 1735 Technical Information Manual preview
A 1735
Brand: Caen Pages: 14
GarrettCom Industrial Network Track OSI Brochure preview
Industrial Network Track OSI
Brand: GarrettCom Pages: 10
Adaptec 2410SA - Serial ATA RAID Controller Hardware Installation Manual preview
2410SA - Serial ATA RAID Controller
Brand: Adaptec Pages: 14
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Brand: PADAUK Pages: 27
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Brand: Meinberg Pages: 14
Olivella Modular Signos User Manual preview
Signos
Brand: Olivella Modular Pages: 19

Brands by name

Popular brands

Load more brands