manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

164

Section 7: DMA

 Document

1250_1125-UM100CB-R

47:32

high_watermark  16'b0 

This specifies the high watermark for generating an interrupt to the CPU based on 
the number of descriptors.
If the MAC receiver is asserting flow control and the number of descriptors rises 
above this watermark it will remove the flow control. 

63:48

low_watermark 

16'b0 

This specifies the low watermark for generating an interrupt to the CPU based on 
the number of descriptors.
The MAC receiver will assert flow control when the number of descriptors falls 
below this watermark. 

Table 91:  Ethernet and Serial DMA Configuration Register 0

 (Cont.)

Table 92:  Ethernet and Serial DMA Configuration Register 1 

dma_config1_mac_0_rx_ch_0 - 

00_1006_4808

     dma_config1_mac_0_tx_ch_0 - 

00_1006_4C08

dma_config1_mac_0_rx_ch_1 - 

00_1006_4908

     dma_config1_mac_0_tx_ch_1 - 

00_1006_4D08

dma_config1_mac_1_rx_ch_0 - 

00_1006_5808

     dma_config1_mac_1_tx_ch_0 - 

00_1006_5C08

dma_config1_mac_1_rx_ch_1 - 

00_1006_5908

     dma_config1_mac_1_tx_ch_1 - 

00_1006_5D08

dma_config1_mac_2_rx_ch_0 - 

00_1006_6808

     dma_config1_mac_2_tx_ch_0 - 

00_1006_6C08

dma_config1_mac_2_rx_ch_1 - 

00_1006_6908

     dma_config1_mac_2_tx_ch_1 - 

00_1006_6D08

dma_config1_ser_0_rx - 

00_1006_0408

   dma_config1_ser_0_tx - 

00_1006_0488

dma_config1_ser_1_rx - 

00_1006_0808

   dma_config1_ser_1_tx - 

00_1006_0888

Bits

Name

Default

Description

0 

hdr_cf_en 

1'b0 

If this bit is set then the L2_cacheable bit will be asserted during header 
transfers to cause the L2 cache to be allocated. 

1 

asic_xfr_en 

1'b0 

Set to enable special support for transferring packets to an ASIC on the 
HyperTransport fabric (or PCI bus). 

2 

pre_addr_en 

1'b0 

Set when asic_xfr_en is set to enable prepending of the DMA descriptor to the 
packet sent to the ASIC. 

3 

flow_ctl_en 

1'b0 

Set to cause the controller to send a flow control request to the interface when 
the descriptor count falls below the low watermark, and only remove the 
request when the count goes above the high watermark. MAC receive 
channels only, setting this bit in other channels causes UNDEFINED behavior. 

4 

no_dscr_updt 

1'b0 

Set to prevent the descriptor being written with the status at the end of a packet 
transfer, saving bandwidth through the bridge. (Transmit channels only.)

5 

dscr_l2ca 

1'b0 

This bit sets the L2 cacheability for descriptors. If it is set the L2CA bit will be 
set in descriptor requests, causing them to be cached in the L2 cache. If clear 
the descriptors will not be allocated in the L2 on a miss.

6 (rx) 

xtra_status

(tx) cpu_pause_en

1'b0 

Ethernet Receive channels only: This bit should only be set for the Ethernet 
receive engine and only if the system revision indicates PERIPH_REV3 or 
greater. If this bit is set the a_size field will be overwritten with additional status 
information in the start of packet descriptor.

Ethernet Transmit channels only: This bit should only be set for the Ethernet 
transmit engine and only if the system revision indicates PERIPH_REV3 or 
greater. If this bit is set the channel will pause at the end of the current packet 
and will resume only when the bit is cleared.

7 

fc_pause_en 

1'b0 

Ethernet Transmit channels only: This bit should only be set for the Ethernet 
transmit engine and only if the system revision indicatess PERIPH_REV3 or 
greater. If this bit is set and the interface is set for DMA channel based flow 
control (ch_base_fc_en bit set in the 

mac_vlantag

 register) then this channel 

will be paused by a flow control frame, if this bit is clear and the interface is set 
for DMA channel based flow control the channel will not be paused by a flow 
control frame. If the interface is not configured for DMA channel based flow 
control this bit is ignored.

15:8 reserved  8'b0 

Reserved

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
Roland MSL-15 Owner'S Manual preview
MSL-15
Brand: Roland Pages: 12
EK-Quantum Kinetic FLT 80 D5/DDC Body User Manual preview
Kinetic FLT 80 D5/DDC Body
Brand: EK-Quantum Pages: 16
Zoom 4412A User Manual preview
4412A
Brand: Zoom Pages: 48
National Instruments PCI-6110E/6111E User Manual preview
PCI-6110E/6111E
Brand: National Instruments Pages: 113
Intel F-Tile SDI II Intel Agilex User Manual preview
F-Tile SDI II Intel Agilex
Brand: Intel Pages: 39
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
Dataprobe iBoot-Exp Manual preview
iBoot-Exp
Brand: Dataprobe Pages: 5
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
Aaeon SBC-555 Manual preview
SBC-555
Brand: Aaeon Pages: 72
Rolls HR11C - SCHEMA Wiring Diagram preview
HR11C - SCHEMA
Brand: Rolls Pages: 1
Ista AMF2.0 Operator'S Manual preview
AMF2.0
Brand: Ista Pages: 16
NXP Semiconductors RDGD3160I3PH5EVB User Manual preview
RDGD3160I3PH5EVB
Brand: NXP Semiconductors Pages: 21
Qlogic QMI2472 Datasheet preview
QMI2472
Brand: Qlogic Pages: 2
Data Translation DT9835 Getting Started Manual preview
DT9835
Brand: Data Translation Pages: 62
NuDAQ ACL-8112 Series User Manual preview
ACL-8112 Series
Brand: NuDAQ Pages: 92

Brands by name

Popular brands

Load more brands