Introduction
Thank you for purchasing the BRIO™ BH-200. This headset is designed for use with
Bluetooth enabled phones and provides comfortable and convenient wireless com-
munication. Included with the BH-200 is an AC wall charger (QTC-BH200). The BH-200
offers the following features:
Power / Call Button
Turns headset on / off.
Answers an incoming call when pressed briefly.
Ends a current call when pressed briefly.
Rejects an incoming call when pressed two times.
Status LED / Beeps
Power On – LED illuminates blue for 1 second (along with 1 beep).
Power Off – LED illuminates red for 1 second (along with 1 beep).
Ready For Pairing – LED flashes with blue / red pattern for about 3 minutes or
until BH-200 is connected to a compatible phone. BH-200 changes to Connectable
if not paired within 3 minutes.
Connectable – LED flashes blue every 5 seconds until paired to a phone or until
there is an active connection with your phone.
Connection Active – LED double flashes blue every 8 seconds.
Incoming Call – LED flashes blue three times per second.
Call Ended – Single beep.
Low Battery – LED flashes about one time per second and headset beeps every
20 seconds.
Volume Up Button – Increases audio level from headset speaker.
Volume Down Button – Decreases audio level from headset speaker.
1.
■
■
■
■
2.
■
■
■
■
■
■
■
■
3.
4.
Charger Connection – For charging the headset’s internal battery.
Headset Speaker – Directs caller’s voice into your ear. Removable speaker cover
has 15 mm diameter.
Earhook – Attaches to headset below speaker. Position over / behind your ear to
hold headset in place. See section Adjusting For Use On Either Ear.
Microphone – Picks up your voice during a call.
Optional Speaker Cover – The extra speaker cover is 18 mm in diameter. This
larger size cover can be used if the 15 mm cover (installed on headset at factory)
feels too loose in your ear.
Action / Condition
Status LED
Headset Speaker
Headset is switched on (power on)
Illuminates blue for 1 second Beeps once
Headset is switched off (power off) Illuminates red for 1 second
Beeps once
Headset is switched on, but is
not paired or does not have an
active connection with a phone
(connectable)
Briefly flashes blue every
5 seconds
N/A
Headset and phone are connected
(connection active)
Double flashes blue every
8 seconds
N/A
Headset is waiting to be paired
with a phone (ready for pairing)
Flashes in blue / red
pattern for about 3 minutes
N/A
Incoming call
Flashes blue three times
per second
N/A
Call ended
N/A
Beeps once
Headset connected to charger and
charging not complete
Illuminates red while
battery is charging
N/A
Headset connected to charger and
charging complete
No illumination
N/A
Battery charge level is low
Flashes quickly (about one
time per second) with color
dependent on headset
status
Beeps once every
20 seconds
Number called is busy
Flashes blue / red alter-
nately every 5 seconds
N/A
5.
6.
7.
8.
9.
Charging The Internal Battery
Important: Before initial use, charge the BH-200’s internal battery for 2 hours. Only
charge with the QTC-BH200 supplied or other approved chargers. When fully charged,
the battery will provide up to 8 hours of talk time and 200 hours of standby time. For
best battery performance, use and store the BH-200 at temperatures between 0º and 45º C
(32º and 113º F). The internal battery is not replaceable. The battery may be charged and
discharged hundreds of time, but will eventually wear out. Recycle the battery when it
no longer holds a charge. Do not dispose of headset or battery as household waste.
Connect the small end of the QTC-BH200 cable to the headset’s charger connec-
tion (see callout 5).
Plug the other end into a wall outlet (AC 120V / 220V). While BH-200 is charging,
the Status LED is red.
When the headset is fully charged, Status LED is off. Unplug the charger from the head-
set and the wall outlet. Do not leave a fully charged battery connected to the charger.
Switching The Headset On / Off
To switch on, press and hold the Power / Call Button for 2 seconds. The headset
beeps once and the Status LED illuminates blue for about 1 second. When the head-
set is switched on the first time, press and hold the Power / Call Button for 5 seconds.
To switch off, press and hold the Power / Call button for 2 seconds. The headset
beeps once and Status LED momentarily flashed red.
Pairing Headset To A Phone
Pairing is the process of linking BH-200 to a Bluetooth enabled phone. The BH-200
may be paired with up to 8 Bluetooth enabled phones, but used with only one phone
at a time. The pairing process must be completed with each phone you want to use.
Charge the BH-200’s internal battery, then follow these steps to pair the headset to
your phone:
Switch on BH-200 and your Bluetooth enabled phone. BH-200 must be within 30’
of the phone for pairing to be completed.
Press the Volume Up and Volume Down Buttons simultaneously for 2 seconds.
When the Status LED flashes in a blue / red pattern, release the buttons. BH-200
is in pairing mode.
Activate the Bluetooth feature on your phone. Set the phone to search for Blue-
tooth devices. See your phone’s user manual for more detailed instructions.
Select BRIO BH-200 from the list of displayed devices.
Enter pass code 0000 to pair and connect BH-200 to your phone. Note: Some
phones pair first, then connect. See user manual for phone.
When connected, BH-200 beeps once and the Status LED double flashes blue every
8 seconds. BH-200 is ready to be used with your phone.
■
■
■
1.
2.
3.
4.
5.
6.
3
1
2
6
BH-200 User Manual
4
5
7
8
Front
Back
9