Not for
Reproduction
Copyright © 2014. All rights reserved. No part of this material may be reproduced or transmitted in any form without the express written permission of Briggs & Stratton Power Products Group, LLC.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
Unpack pressure washer
1. Remove everything from carton except pressure washer.
2. Open carton completely by cutting each corner from top to bottom.
3. Ensure you have all included items prior to assembly. If items are
damaged or missing, call
1-800-743-4115
.
4. Prior to assembly, lubricate the rubber o-ring seals on all connections
with petroleum or synthetic grease. See Operator’s Manual,
Lubricate
O-Rings
.
10
11
12
14
15
Assemble pressure washer
1. Place handle (A) onto handle supports (B) connected to main
unit. Make sure holes (C) in handle align with holes (C) on handle
supports.
1
2. Insert handle carriage bolts (D) through holes from inside of unit and
attach a plastic knob (E) from outside of unit. Tighten by hand.
2
NOTICE
By loosening both knobs to the unthreaded middle section of
attachment bolt, the upper handle can fold forward to store flat atop the
cold engine. DO NOT fold handle down while the engine is hot.
3. Insert rubber strap (F) through slot (G) in back of accessory tray and
pull tight from front.
3
4. Place accessory tray (J) over holes (H) on handle (viewing from
front of unit). Push the tree clips (K) into the holes until they sit flat
against the accessory tray.
4
5. Insert supplied accessories in spaces provided in accessory tray. See
How to Use Accessory Tray
.
Connect battery cable
Your unit is equipped with push start capability but can be started
manually. If you choose not to use the push start feature, you do not
need to connect the battery cable. The sealed battery on the pressure
washer is pre–installed except for the two-pin cable.
1. Connect two-pin connectors on top right side of pressure washer
base toward the back (veiwing from side of unit).
5
2. Verify that connections to battery and pressure washer are tight and
secure.
NOTICE
Charge battery for 24 hours prior to first use following the
instructions in the section
Battery Charger
of the Operator’s Manual.
Add engine oil and fuel
NOTICE
You MUST properly fill engine with oil before attempting to
start pressure washer.
NOTICE
DO NOT use unapproved gasoline such as E15 and E85. DO
NOT mix oil in gasoline or modify engine to run on alternate fuels.
1. Move pressure washer outdoors to a flat, level surface.
2. Clean area around oil fill and remove oil fill cap/dipstick ( ).
6
3. Hold neck of supplied oil pouch and remove cap.
4. Slowly pour contents of oil pouch into oil fill opening. Checking oil
level frequently, fill to FULL mark (top hole) on dipstick.
7
NOTICE
Pause to permit oil to settle. Wipe dipstick clean each time oil
level is checked. DO NOT overfill.
5. Replace and fully tighten oil fill cap/dipstick.
6. Clean area around the fuel cap ( ), remove fuel cap.
6
7. Slowly add clean, fresh, UNLEADED fuel (M) to fuel tank (L). Be
careful not to overfill. To allow for fuel expansion, do not fill above
the bottom of the fuel tank neck.
8
8. Replace fuel cap. Let any spilled fuel evaporate before starting
engine.
Move pressure washer to safe
operating location
1. Move pressure washer outdoors to a flat, level surface.
9
2. Keep at least 5 ft. (1.5 m) clearance on all sides of pressure washer
including overhead to reduce the risk of exhaust heat or exhaust
gases igniting nearby combustible material.
Connect spray gun
NOTICE
Remove and discard the shipping caps from the pump’s high
pressure outlet and water inlet before attaching hoses.
1. Uncoil high pressure hose (P) and attach one end of hose to base of
spray gun (N). Tighten by hand.
10
2. Attach other end of high pressure hose (P) to high pressure outlet
(Q) on pump. Tighten by hand.
11
Connect water supply
1. Inspect garden hose inlet screen (R) for damage.
12
NOTICE
If inlet screen is damaged or missing, DO NOT use pressure
washer, call
1-800-743-4115
.
2. Clean screen if necessary. Refer to operator’s manual for instructions.
3. Run cold water through garden hose (S) for 30 seconds to clean out
any debris. Garden hose length must not exceed 50 ft. (15 m). Turn
off water supply and attach garden hose to water inlet (T). Tighten by
hand.
12
Start pressure washer
NOTICE
You MUST connect and turn on water supply fully before
starting engine.
1. Put on safety goggles.
2. Turn on water supply.
3. Point gun in a safe direction and press red safety button (U) on spray gun
and pull trigger until water comes out in a steady stream.
13
4. Attach nozzle extension (V) to spray gun (N). Tighten by hand.
14
5. Pull back on collar of nozzle extension (V), insert 7-in-1 nozzle (W)
and release collar. You may have to twist 7-in-1 nozzle (W) to seat
properly in nozzle extension (V). Tug on 7-in-1 nozzle (W) to make
sure it is securely in place.
15
6. Push engine rocker switch (X) to ON (I) position.
16
NOTICE
This unit is equipped with a ReadyStart® engine. A
ReadyStart® engine requires no priming or choking.
NOTICE
Always unplug battery charger before starting pressure
washer.
7. Start pressure washer using Push Button Start or Manual Mode:
For Push Button Starting,
push and hold button (Z) until pressure
washer starts. To prolong the life of starter components, DO NOT
hold button for more than 5 seconds, and pause for at least
30 seconds between starting attempts.
17
For Manual Starting,
position yourself as recommended and grasp
starter grip handle and pull slowly until you feel some resistance. Then
pull rapidly to start engine. Return starter grip handle slowly. DO NOT let
rope “snap back” against starter.
18
NOTICE
After each starting attempt, where engine fails to run, always
point gun in safe direction press the red safety button (U) and squeeze
spray gun trigger to release high pressure.
13
8. Point gun toward surface to be cleaned. Press the red safety button
(U) and pull trigger to begin spraying.
13
Stop pressure washer
1. Release spray gun trigger and let engine idle for two minutes.
2. Push engine rocker switch (X) to OFF (O) position.
16
3. Turn off water supply.
4. Point spray gun in safe direction, press red safety button, and
squeeze spray gun trigger to relieve retained high water pressure.
Spray gun traps high water pressure, even when engine is stopped
and water is disconnected.
5. Disconnect garden hose from pump.
6. Disconnect high pressure hose from pump and gun for storage. For
long term storage instructions, see operator’s manual.
7. Remove safety goggles.
Items Included:
Operator’s Manual (not shown)
Quick Setup Guide
Pressure Washer
Have Questions?
Do not return to store. We can help.
Call Customer Service Toll-Free
1-800-743-4115
or visit our website,
BRIGGSandSTRATTON.com
Oil Pouch (1)
18
WARNING
Failure to read and follow the operator’s
manual and all operating instructions could
result in death or serious injury.
WARNING
Fuel and its vapors are extremely
flammable and explosive which could cause
burns, fire or explosion resulting in death or
serious injury. Turn pressure washer engine
OFF and let it cool at least 2 minutes before removing
fuel cap. Let spilled fuel evaporate before starting
engine. Always allow space for fuel expansion.
WARNING
Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster
than you can let go which could cause broken
bones, fractures, bruises, or sprains resulting
in serious injury. NEVER pull starter cord without first
relieving spray gun pressure. Pull starter cord slowly
until resistance is felt, then pull rapidly. Firmly grasp
spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
WARNING
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in minutes.
You CANNOT smell it, see it, or taste it. Operate
ONLY outside far away from windows, doors and
vents. Install carbon monoxide alarms. DO NOT run this
product inside homes or garages, even if using fans or
opening doors and windows.
WARNING
High water pressure could cut through
skin resulting in serious injury. Spray gun traps
high water pressure, even when engine is
stopped and water is disconnected. NEVER aim
spray gun at people, animals, or plants. ALWAYS point
spray gun in safe direction, press red button and
squeeze spray gun trigger to release high pressure,
every time you stop engine.
WARNING
Risk of eye injury. Spray could splash
back or propel objects resulting in serious injury.
Always wear indirect vented (chemical splash)
safety goggles marked to comply with ANSI
Z87.1 when using or in vicinity of this equipment. NEVER
substitute safety glasses or dry-condition goggles for
indirect vented safety goggles.
Items not included (you will need):
• Utility knife • Unleaded fuel • Garden hose, 50 ft. (15 m) or less
• Safety goggles (indirect vented type) • Petroleum or synthetic grease
WARNING
Engine exhaust contains carbon monoxide, a poisonous
gas that could kill you in minutes. You CANNOT smell it, see it,
or taste it. Operate ONLY outside far away from windows, doors
and vents. Install carbon monoxide alarms. DO NOT run this
product inside homes or garages, even if using fans or opening doors and
windows.
WARNING
Risk of eye injury. Spray could splash back or propel
objects resulting in serious injury. Always wear indirect
vented (chemical splash) safety goggles marked to comply
with ANSI Z87.1 when using or in vicinity of this equipment.
NEVER substitute safety glasses or dry-condition goggles for indirect
vented safety goggles.
WARNING
Starter cord kickback (rapid retraction) will pull hand
and arm toward engine faster than you can let go which
could cause broken bones, fractures, bruises, or sprains
resulting in serious injury. NEVER pull starter cord without
first relieving spray gun pressure. Pull starter cord slowly until
resistance is felt, then pull rapidly. Firmly grasp spray gun with both
hands when using high pressure spray to avoid injury when spray gun
kicks back.
X
16
W
V
15
U
13
10
Exhaust port
pointed away from
occupied spaces
9
V
14
N
R
S
12
T
N
P
P
11
Q
WARNING
Battery posts, terminals and related accessories contain
lead and lead compounds - chemicals known to the State of California
to cause cancer and reproductive harm. Wash hands after handling.
1
A
C
B
C
3
F
G
2
E
D
4
H
J
K
5
Full
Add
7
6
L
M
8
Z
17
