Bridgeview Bale King 6100 Operator'S & Parts Manual Download Page 23 | Manualshive

Page: 23 / 65

background image

Bale King 6100 – Operator and Parts Manual

23 / 65

Maintenance and trouble shooting

This section drives you through some maintenance, troubleshooting tips.

BEFORE ATTEMPTING ANY REPAIR PROCEDURES,

ALWAYS USE APPROPRIATE EQUIPMENT SUCH AS

SAFETY GLASSES, SAFETY SHOES, AND GLOVES

Power take-off

NOTE: Use ONLY genuine Weasler parts when replacing any worn or damaged PTO

components.

PTO Shield

Shield Removal

•

To remove the shield, pop out the red snap, then

rotate  the  guard  on  the  bearing  to  line  up  the  three  tabs
with  the  openings  and  pull  it  off  away  from  the  knuckle
joint.  Remove  the  nylon  bearing  from  the  shaft  by
spreading it open.

Shield Assembly

Be sure to lubricate the groove in the inner yokes where the shield

bearing rides. Reinstall shields in the reverse order that they were
removed.

Verification on the shield

The entire shield must turn freely on the shaft. Operating without shields can cause

serious injury to the operator.

«
...
21
22
23
24
25
...
»

Summary of Contents for Bale King 6100


































































Reviews:

No comments

Related manuals for Bale King 6100

Brand: Labnet Pages: 5

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: Bartscher Pages: 28

Brand: Bartscher Pages: 13

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

BODY ARMOR PRO TERM

Brand: Darco Pages: 6

MET ONE 3400 Series

Brand: Hach Pages: 48

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brand: laguna Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands