manualshive.com logo in svg

Bridgeview Bale King 6100, Operator'S & Parts Manual

Share
Download
Bridgeview Bale King 6100 Operator'S & Parts Manual Download Page 22

 

Bale King 6100 – Operator and Parts Manual                                   

22 / 65 

Processing bale

 

 

Set hoop grate according to the table on page 11.  Adjust fine chop if your machine is 
equipped with it. 

1.

 

 Engage the PTO when the tractor is idle. 

2.

 

Raise PTO speed to  1000 RPM  

3.

 

Set  deflector:  -  Bedding  –  deflector  fully  raised  /  Windrow  –  deflector 
fully lowered 

4.

 

Rotate  bale  with  agitators  left  or  right.  Reverse  directions  periodically  to 
ensure even processing. (Approx agitator speed is 32 – 34 RPM. 

Unhook the machine

 

Shut OFF the tractor and remove the key before unhooking the machine. 

Make sure the processor is empty to prevent damage to the hitch jack. 

1.

 

Support the processor with the hitch jack. 

2.

 

Unhook hydraulics, electrical harnesses and the PTO shaft. Arrange them 
on PTO holder. 

3.

 

Remove hitch pin.  

Twine Removal 

•

 

Twine or net wrap should be removed after approximately 25 bales.  

•

 

Excessive  twine  build-up  may  hinder  flail  operation,  can  cause  rotor 
imbalance and will make removal more difficult. 

Summary of Contents for Bale King 6100


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands