manualshive.com logo in svg

Bridgeview Bale King 6100, Operator'S & Parts Manual

Share
Download
Bridgeview Bale King 6100 Operator'S & Parts Manual Download Page 20

 

Bale King 6100 – Operator and Parts Manual                                   

20 / 65 

Working Angle 

Constant  Velocity  joints  can  operate  up  to  80  degrees  for 

short periods of time. Do not operate for long periods on 
sharp angles. 

Attachment 

Be  sure  the  drive-line  is  properly  attached  and  all  bolts  and 

screws  are  tight  on  the  implement  input  shaft  and  on  the 
tractor PTO shaft 

Storage 

When  not  in  use,  cover  or  protect  the  drive  shaft  from  the  the 

elements.  When  removed  from  the  machine  store  both  halves  together  to  prevent 
damage.    Check  all  components  for 
proper  function  and  lubrication 
before use. 

Hook up the machine

 

1.

 

Connect  Bale  King  to  tractor 
drawbar 

2.

 

Shut OFF the tractor. 

3.

 

Hook up PTO, hydraulic hoses, light 
plug  and  the  electrical  harness  into 
the control box.  

4.

 

Remove  the  jack  stand  and  attach  it 
to  the  storage  jack  stub  located  on 
the left side of the machine. 

5.

 

Attach the safety chain to a secure and safe location on the tractor.  

6.

 

 Visually inspect and verify that the tractor and processor are safe to operate.  Perform 
any required performance checks to ensure the equipment will operate as expected. 

Summary of Contents for Bale King 6100


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands