manualshive.com logo in svg

Bridgeview Bale King 6100, Operator'S & Parts Manual

Share
Download
Bridgeview Bale King 6100 Operator'S & Parts Manual Download Page 19

 

Bale King 6100 – Operator and Parts Manual                                   

19 / 65 

Loading deck

 

The Bale King 6100 can carry 5 

bales on the deck and 1 bale 
inside the tub. It is equipped 
with  a  pair  of  heavy  duty 
conveyor  chains  to  load 
bales.  Set  the  flow  rate  on 
the  tractor  for  the  desired 
loading speed.  

Torflex axles

 

The Bale King  is equipped  with 

a  pair  of  Torflex  axles  that 
allow  a  smooth  ride  over 
rough terrain. .  

Safety Operation 

 

Power and take off Use

 

Prior  to  first  use  of  the  Bale  King,  the  PTO  connectors  and  shaft  length  must  be 

adjusted to your tractor.  

 Length 

Confirm  the  minimum  and  maximum  working  lengths  of  the 

drive-line. The telescoping tubes must overlap at least 1/3 
of  their  length  when  in  use.    The  PTO  is  designed  to  be 
used with a drawbar length of 16" from the end of the PTO 

shaft. Adjust your tractor accordingly. 

Shielding 

Be  sure  that  the  shielding  is  not  damaged 

and rotates freely on the drive shaft. 

Summary of Contents for Bale King 6100


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands