Brave VH1724GC Page 39 Owner'S Manual Download | Manualshive

Page: 39 / 62

background image

39

Assembly Instructions

Step 1 – Wheels to Axle Assembly



Remove everything from the axle (protective wrap, nut, washer, and
cotter key).



Slide wheel onto axle with valve stem facing out.



Slide wheel washer up against the wheel bearing.



Torque the axle nut to 30-40 ft.-lb.



Rotate tire to ensure proper bearing seating.



Loosen the axle nut until loose enough to turn the axle nut with your
fingers.



Re-tighten the axle nut until finger tight.



Insert the cotter pin through the hole in axle nut and axle. Bend and
spread prongs in opposite directions so the axle nut will not come off
(make sure the wheel spins freely).



Use dust cap tool and hammer to install the dust cap on the wheel hub,
placing a small square of scrap lumber over the dust cap tool and
tapping with the hammer. Tap until the dust cap is well seated against
the hub.



Repeat step for the other side.

Tools Needed



Torque Wrench



Pliers



Hammer



Dust Cap Tool



38mm Socket



Ratchet

Components Needed from Parts Bag:

Part # 780598

Dust Cap

Qty: 2

Wheel
Bearing

Wheel

Cotter Pin

Axle Nut

Dust Cap

Axle

Wheel
Washer

Part # 780599

White Plastic

Dust Cap Tool

Qty: 1

«
...
37
38
39
40
41
...
»

Summary of Contents for VH1724GC































































Reviews:

No comments

Related manuals for VH1724GC

Brand: ATIKA Pages: 146

Brand: North American Tool Pages: 8

Brand: sunjoe Pages: 24

Brand: Sealey Pages: 5

Brand: Gude Pages: 68

Brand: Gude Pages: 76

Brand: Gude Pages: 92

Brand: Super Handy Pages: 12

Brand: Super Handy Pages: 12

Brand: Super Handy Pages: 12

Brand: Hud-son Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands