background image

Sa

fe

ty

 in

for

m

at

ion

9

Occupant restraints

400mm

(16in)

FCZ

HHT

200mm

(8in)

200mm

(8in)

• 

Wheelchair users, their carers and family are advised to check vehicle 

specifications to ensure that sufficient floor space is available to 

accommodate the wheelchair and tie-down system. These distances 

are based upon the desire to maintain clear zones for potential head 

excursions of occupants provided with both upper and lower torso 

restraints. 

• 

Users of heavy powered wheelchairs are also advised to check vehicle 

carrying capacity. If in doubt consult the vehicle supplier for further 

details. 

• 

Any airbag, as fitted to the vehicle, shall be used only as a 

supplementary occupant restraint if designed to be used in 

combination with the WTORS. 

• 

Installers of this tie-down should take note of any vehicle airbag 

position when planning the installation. Airbags can cause serious 

injury if a wheelchair-seated occupant is seated too close to an airbag 

position. If in doubt contact the vehicle manufacturer or your National 

Automotive Regulatory Body for advice.

Figure A

Summary of Contents for TOR LAP BELT



















Reviews: