Braun SpaceCom Service Manual Download Page 11

Page: 11 / 126

SpaceStation, 2.0 gb

0 - 11

0 -

Contact Persons

Technical Training

Via local representative.

Entry for Technical Training

Application for a technical training course must be made via the

responsible representative.

Ordering of Spare Parts and Test Equipment

Please contact your local B. Braun subsidary.

International Technicians (Intercompany)

Nadja Machal

Fax:

+49 5661 / 75 -47 89

e-mail:

[email protected]

Service Hotline

Karl Tippel, Tanja Kördel

Phone:

+49 5661 / 71 - 35 25

Fax:

+49 5661 / 71 - 35 26

e-mail:

[email protected]

e-mail:

[email protected]

Return of Spare Parts and Test Equipment

B. Braun Melsungen AG
Schwarzenberger Weg 73-79
Wareneingang Werk C
34 212 Melsungen
Germany

Safety Officer

(§ 30 MPG)

Dr. Ludwig Schütz

e-mail: [email protected]

Translation

PAS GmbH, Brückner GmbH, Germany

2.0

Summary of Contents for SpaceCom































































































































Search results

Summary of Contents for SpaceCom

Reviews:

Brands by name

Popular brands

Braun SpaceCom, Service Manual

Search results

Summary of Contents for SpaceCom

Reviews:

Brands by name

Popular brands