background image

Page 15

Maintenance and Lubrication Schedule

Use Braun 87010R (5606 aviation 

fl

uid).  Do 

not mix with Dextron III or other hydraulic 

fl

uids.  

Check 

fl

uid level with platform lowered fully.  Fill 

to maximum 

fl

uid level indicated on reservoir 

(speci

fi

ed on decal).  Do not over

fi

ll.  If 

fl

uid level 

decal is not present - measure 7/8" from the bot-
tom of 

fi

ll tube to locate 

fl

uid level.

Replace if needed. 

Tighten or replace if needed

Check to see that the lift is securely anchored to 
the vehicle and there are no loose bolts, broken 
welds, or stress fractures.

Replace decals if worn, missing or illegible.  Re-
place antiskid if worn or missing.

Consecutive 

750 Cycle 

Intervals

4500 

Cycles

Inspect platform cable-activated manual release 
system (T-handle/cable assembly and carriage 
movement) 

Inspect limit switches and cams for securement 
and proper adjustment

Inspect carriage, lifting arm and eccentric shaft 
rollers (bearings) for wear or damage, positive 
securement and proper operation 

Inspect external snap rings (e-clips): 
• Carriage roller bearings (4)
• Lower lifting arm pins (5)
• Upper lifting arm pins (2)
• Outer race bearings (2)
• Inner roll stop shaft (2)

Inspect lower lifting arm pins for wear or damage, 
positive securement and proper adjustment

Inspect eccentric shaft pins, bearing mounting 
screw, washers and securement hardware for 
wear or damage, positive securement and proper 
operation

Inspect torque tube cams for securement, wear or 
damage

Inspect housing cam brackets for securement, 
wear or damage

Inspect cylinder(s), hoses, 

fi

ttings and hydraulic 

connections for wear, damage or leaks 

Inspect power cable 
 

 

Ensure T-handle release and cable assembly op-
erate properly.  Ensure carriage can be manually 
extended and retracted freely.

Resecure, replace or adjust as needed.  See 
Adjustments and Calibration section. 

Correct, replace damaged parts and/or relubricate.

Resecure, replace or correct as needed.

Resecure, replace damaged parts, lubricate or 
correct as needed.

Resecure, replace damaged parts, lubricate or 
correct as needed.  See Carriage Ride Height 
Adjustment.

Resecure, replace or correct as needed.

Resecure, replace or correct as needed.

Tighten, repair or replace if needed. 

 

 

Resecure, repair or replace if needed.

1500 

Cycles

Repeat all previously listed inspection, lubrica-
tion and maintenance procedures at 750 cycle 
intervals.

Hydraulic Fluid (Pump) - Check level.  Note:  Fluid 
should be changed if there is visible contamina-
tion.  Inspect the hydraulic system (cylinder, hoses, 

fi

ttings, seals, etc.) for leaks if 

fl

uid level is low.

Inspect lifting arm bushings and pivot pins for vis-
ible wear or damage

Inspect outer barrier pivot pin mounting bolts (2)

Mounting 

Decals and Antiskid

Summary of Contents for Under-Vehicle Lift A1 Series









































Reviews: