Bradley Terreon Multi-Fount Series Installation Instructions Manual Download Page 1

Bradley Multi-Fount™ Series

MF2949/IR

Terreon

® 

Quadra-Fount

Wall-Hung Washfountain
with Adaptive Infrared
Control

(Standard* & Juvenile Height)

*ADA compliant when mounted at recommended
heights

Installation
Instructions

Table of Contents

Pre-Installation Information  . . . . . . . . . . . . . . . . . . . .2
Washfountain Component Parts  . . . . . . . . . . . . . . . . .3
Installation Instructions . . . . . . . . . . . . . . . . . . . . .4-10
Cleaning Instructions . . . . . . . . . . . . . . . . . . . . . .11-12
Solenoid Valve Troubleshooting  . . . . . . . . . . . . . . .13

215-1249 Rev. H; EN 03-045
© 2003 Bradley Corporation 
Page 1 of 13

9-15-2003

P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY

FAX  262-251-5817

http://www.bradleycorp.com

IMPORTANT

Read through this installation manual to
ensure proper installation.

Make sure that water supply is completely
off before installation is begun.

When drilling into tile, masonry, or other
hard materials to install wall and floor
anchors, be sure to wear safety goggles
to prevent eye injuries.

Wall anchors used must have a minimum
pull-out rating of 1,000 lbs.

The Quadra-Fount™ requires a water
flowing pressure of at least 20 psi but no
greater than 100 psi.

File these instructions with the owner or
maintenance department.

Summary of Contents for Terreon Multi-Fount Series














Reviews: