background image

9

Installation 

S19-323, S19-324

Bradley • 

215-1846 Rev. C; ECN 17-05-068 

11/21/2017

Servicing of Lights

S19-324 Halogen Lights (Type 4X)

A

De-power the control box by 
observing standard lock-out tag-out 
practices .

B

To disconnect the wire leads of the 
light requiring the bulb to be replaced, 
use a small blade screwdriver to 
depress the orange terminal release 
tab adjacent to the wire's location . 
With the tab fully depressed, the 
wire can be easily removed from the 
terminal location .

C

Remove the nut on the stem of 
the light which attaches it to the 
enclosure . Remove the entire light .

D

Remove the gasket (if present) to 
expose the four screws which retain 
the dome .

E

Remove the screws, take off the 
dome and the twist lock bulb is now 
visible . Press and turn the bulb to 
remove . Replace as needed with the 
same size bulb .

F

Reverse the disassemble process to 
reinstall the light . Inspect all gaskets 
and seals to ensure the integrity of 
the unit .

G

Check that the signaling station is 
functioning properly once the power 
is restored by activating the fixture 
attached to the signaling station .

S19-323 Signal Light (Type 3R)

A

De-power the control box by 
observing standard lock-out tag-out 
practices .

B

To disconnect the wire leads of the 
light requiring replacement, use a 
small blade screwdriver to depress 
the orange terminal release tab 
adjacent to the wire's location . With 
the tab fully depressed, the wire can 
be easily removed from the terminal 
location .

C

Remove the 2 nuts on the studs 
which attach the light to the enclosure 
and remove light . This is a sealed 
light and has no serviceable 
components, the complete housing 
must be replaced .

D

Using the old light for reference, 
prepare the replacement light's 
lead wire and exposed conductor's 
lengths .

E

Reverse the disassemble process to 
reinstall the lamp . Be sure to use the 
new gasket provided with the new 
light .

F

Check that the signaling station is 
functioning properly once the power 
is restored by activating the fixture 
attached to the signaling station .

Summary of Contents for S19-323















Reviews: