manualshive.com logo in svg

BR-Automation Automation PC 820, User Manual, Page: 79 / 252

Share
Download
BR-Automation Automation PC 820 User Manual Download Page 79

Commissioning • Installation

Chapter 3

Com

m

is

sio

ning

79

Automation PC 820 User's Manual V 1.00

1.4  Mounting the APC820

The following must be taken into consideration when attaching to mounting plates:

•

Attach the APC820 to the mounting plate using the mounting clip(s) on the top.

•

Clip the APC820 into the backplane module. 
The APC820 must be thoroughly attached, so that it rests straight in the backplane
module in order for the module contacts to function properly.

•

Tighten all M6 mounting screws (2 screws per module width) on the APC820 with a

torque of max. 5 Nm

.

Information:

The Automation PC820 must always be secured to the first position of the mounting
plate.

Figure 25: Attaching modules

Summary of Contents for Automation PC 820





























































































































































































































































Reviews:

No comments