manualshive.com logo in svg

BR-Automation Automation PC 820, User Manual, Page: 36 / 252

Share
Download
BR-Automation Automation PC 820 User Manual Download Page 36

36

Technical data • Entire device

Automation PC 820 User's Manual V 1.00

2.2  Temperature specifications

2.2.1  Maximum ambient temperature with a fan kit

Caution!

The Automation PC820 must be attached to the first position of the mounting plate.

Figure 9: Ambient conditions with a fan kit

5PC800.B945-02

5PC800.B945-03

Main memory

5MMDDR.0512-01

5MMDDR.1024-01

5MMDDR.2048-01

System unit

5PC820.SX01-00

Maximum ambient temperature

U7500

CM 423

5PC800.B945-00

L2400

5PC800.B945-01

L7400

Add. Plug-in cards

PCIec card slot

What else can be operated at max, ambient

temperature, or are there limitations?

All temperature values in degrees

celsius (°C) at 500 m above sea level.

Derating the maximum ambient temperature

(typically 1°C per 1000 m

above 500 m sea level.

55

55

55

55

5ACPCC.ETH0-00

5ACPCC.MPL0-00

50

5PC800.B945-04

T7400

Summary of Contents for Automation PC 820





























































































































































































































































Reviews:

No comments