manualshive.com logo in svg

BR-Automation Automation PC 820, User Manual, Page: 195 / 252

Share
Download
BR-Automation Automation PC 820 User Manual Download Page 195

Accessories • Overview

Chap

ter 6

Accessories

195

Automation PC 820 User's Manual V 1.00

Chapter 6 • Accessories

1. Overview

Model number

Short description

Note

0AC201.91

Lithium batteries, 4 pcs

.

Lithium batteries, 4 pcs., 3 V / 950 mAh, button cell

4A0006.00-000

Lithium battery (1x)

Lithium battery, 1 pc., 3 V / 950 mAh, button cell

5AC900.1000-00

Adapter DVI-A/m to CRT DB15HD/f

Adapter DVI (plug) to CRT (socket), for connecting a standard monitor
DVI-I interface.

5CFCRD.0512-04

CompactFlash 512 MB B&R

CompactFlash card with 512 MB SLC NAND flash and IDE/ATA interface

5CFCRD.1024-04

CompactFlash 1024 MB B&R

CompactFlash card with 1024 MB SLC NAND flash and IDE/ATA interface

5CFCRD.2048-04

CompactFlash 2048 MB B&R

CompactFlash card with 2048 MB SLC NAND flash and IDE/ATA interface

5CFCRD.4096-04

CompactFlash 4096 MB B&R

CompactFlash card with 4096 MB SLC NAND flash and IDE/ATA interface

5CFCRD.8192-04

CompactFlash 8192 MB B&R

CompactFlash card with 8192 MB SLC NAND flash and IDE/ATA interface

5CFCRD.0064-03

CompactFlash 64 MB SSI

CompactFlash card with 64 MB SLC NAND flash and IDE/ATA interface

5CFCRD.0128-03

CompactFlash 128 MB SSI

CompactFlash card with 128 MB SLC NAND flash and IDE/ATA interface

5CFCRD.0256-03 

CompactFlash 256 MB SSI

CompactFlash card with 256 MB SLC NAND flash and IDE/ATA interface

5CFCRD.0512-03 

CompactFlash 512 MB SSI

CompactFlash card with 512 MB SLC NAND flash and IDE/ATA interface

5CFCRD.1024-03 

CompactFlash 1024 MB SSI

CompactFlash card with 1024 MB SLC NAND flash and IDE/ATA interface

5CFCRD.2048-03 

CompactFlash 2048 MB SSI

CompactFlash card with 2048 MB SLC NAND flash and IDE/ATA interface

5CFCRD.4096-03 

CompactFlash 4096 MB SSI

CompactFlash card with 4096 MB SLC NAND flash and IDE/ATA interface

5CFCRD.8192-03 

CompactFlash 8192 MB SSI

CompactFlash card with 8192 MB SLC NAND flash and IDE/ATA interface

5MMUSB.2048-00

USB flash drive 2 GB SanDisk

USB 2.0 flash drive 2 GB

Summary of Contents for Automation PC 820





























































































































































































































































Reviews:

No comments