manualshive.com logo in svg

BR-Automation Automation PC 820, User Manual, Page: 153 / 252

Share
Download
BR-Automation Automation PC 820 User Manual Download Page 153

Software • Upgrade information

Ch

apte

r 4

Soft

w

are

153

Automation PC 820 User's Manual V 1.00

2. Upgrade information

2.1  BIOS upgrade

An upgrade might be necessary for the following reason:

•

To update implemented functions or to add newly implemented functions or components
to the BIOS setup (information about changes can be found in the Readme files of the
BIOS upgrade).

2.1.1  What information do I need?

Before you begin the upgrade, it helps to determine the various software versions.

Warning!

The BIOS and firmware on APC820 systems must be kept up to date. New versions
can be downloaded from the B&R homepage (

www.br-automation.com

).

Information:

Individually saved BIOS settings are deleted when upgrading the BIOS.

Summary of Contents for Automation PC 820





























































































































































































































































Reviews:

No comments