manualshive.com logo in svg

BR-Automation Automation PC 820, User Manual, Page: 146 / 252

Share
Download
BR-Automation Automation PC 820 User Manual Download Page 146

146

Software • BIOS options

Automation PC 820 User's Manual V 1.00

1.11  BIOS Error signals (Beep codes)

While the Automation PC 820 is booting, the following messages and errors can occur with
BIOS. These errors are signaled by different beeping codes.

1.11.1  BIOS 945GME

Beeping code

Meaning

Necessary user action

1 x short

Memory refresh failed.

Load BIOS defaults. In the event that the error persists, 
send industrial PC to B&R for testing.

2 x short

Parity error: POST error (error in one of the hardware 
testing procedures)

Check the placement of the inserted card. In the event that 
the error persists, send industrial PC to B&R for testing.

3 x short

Base 64 KB memory failure: Basic memory defect, RAM 
error within the initial 64 KB.

Send industrial PC to B&R for checking.

4 x short

Timer not operational: System timer.

Send industrial PC to B&R for checking.

5 x short

Processor error: Processor defect.

Send industrial PC to B&R for checking.

6 x short

8042 gate A20 failure: Keyboard controller defect (block 
8042/ A20 gate). Processor cannot switch to protected 
mode.

Send industrial PC to B&R for checking.

7 x short

Processor exception interrupt error: Virtual mode 
exception error (CPU generated an interrupt error.

Send industrial PC to B&R for checking.

8 x short

Display memory read/write error: Video memory not 
accessible; graphic card defect or not built in (no fatal 
error).

Check inserted graphic card position and eventually 
exchange. In the event that the error persists, send 
industrial PC to B&R for testing.

9 x short

ROM-checksum error: ROM-BIOS-checksum incorrect, 
EPROM, EEPROM or Flash-ROM component defect, 
BIOS defect or incorrectly updated.

Send industrial PC to B&R for checking.

10 x short

CMOS shutdown register read/write error: CMOS cannot 
be read/written.

Send industrial PC to B&R for checking.

11 x short

Cache Error / external Cache bad: L2 - Cache on the 
mainboard is defected.

Send industrial PC to B&R for checking.

Table 109: BIOS post code messages BIOS 945GME

Summary of Contents for Automation PC 820





























































































































































































































































Reviews:

No comments