manualshive.com logo in svg

Boston Scientific Latitude 3300, Operator'S Manual

Share
Download
Boston Scientific Latitude 3300 Operator'S Manual Download Page 55

49

To install the battery:

1.

Insert the new battery (Model 6753) at a slight angle with the battery status
indicators on the top right, to make a secure connection between the
battery and Programmer contacts.

2.

Press down on the left edge of the battery to ensure that the battery is fully
seated, to allow the battery cover to fit flush with the case.

3.

Determine the charge status by pressing the battery status button on the
battery, which is located just above the battery status indicator LEDs

4.

Replace the battery retaining strap.

5.

Replace the battery cover by aligning the left edge of the cover with the
middle of the battery release button (see Figure 30 Battery Compartment
on Underside of the Programmer on page 47).

6.

Close the battery cover by sliding the door to the left until you hear an
audible click.

7.

If the battery charge status is less than 100%, connect the Programmer to
AC power. A full recharge from a depleted battery will take about 2 to 2 1/2
hours.

NOTE:

As long as the Programmer is plugged in (connected to AC

power), the battery will charge. The Programmer does not have to be
powered on to recharge the battery. However, the Programmer must be
turned on in order to check the battery charge status (see Figure 9 Main
Screen on page 25).

NOTE:

For best results, be sure to charge the battery to 100% before

using the Programmer on battery power only.

Battery Recycling

Boston Scientific recommends that the Lithium-ion battery should be
discharged to 25% or less of capacity, and should be recycled in a separate
collection for electrical and electronic equipment. Do not place the battery in
the trash.

NOTE:

Do not include the battery when returning the Model 3300

Programmer to Boston Scientific Corporation.

WARNING:

The Model 6753 Battery is a Lithium-ion battery and, as such, is deemed a
Dangerous Good in regards to shipping. Do not return the Model 6753 battery
to Boston Scientific. Dispose of the battery as required by local regulations. If
the battery must be shipped, contact your local shipper for instructions and
shipping requirements.

If returning the Lithium-ion battery by air shipment, contact Boston Scientific
using the information on the back cover of this manual to obtain the proper
return shipment labeling and requirements.

Summary of Contents for Latitude 3300

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands