Boston Scientific 6498 Patient Manual Download Page 45

Page: 45 / 64

LATITUDE

Communicator Patient Manual

Interrogating Your Implanted Device

The Communicator automatically interrogates your

implanted device on a regular schedule that is set by

your health care provider. This may happen without

your awareness and should not require any action

on your part. Daily device checks are also performed

automatically, without being set by a health care

provider. None of the Communicator indicators will light

during a scheduled interrogation or daily device check.

A scheduled interrogation will not be completed if you

are out of range (10 ft / 3 m) from the Communicator

when it attempts to communicate with your implanted

device. If the Communicator is unable to automatically

interrogate your device after repeated attempts, the

Heart button will flash to allow you to complete the

interrogation manually. The Heart button also flashes

the first time you use the Communicator.

The Heart button is designed to enable you to

manually interrogate your implanted device. Manual

interrogation is a feature that must be enabled by

your health care provider. When you press the Heart

button, the Communicator checks to make sure that

the interrogation is permitted. You should only use the

Heart button if it is flashing or when instructed to do so

by your health care provider.

If you press the Heart button by mistake (not intending

to perform an interrogation), press and hold the Heart

button again for at least 5 seconds to cancel the

interrogation. The Collecting Waves may light yellow

and show progress while the interrogation is being

cancelled.

When using the Heart button, you should stay close

to the Communicator during the entire interrogation

Summary of Contents for 6498

































































Search results

Summary of Contents for 6498

Reviews:

Related manuals for 6498

Brands by name

Popular brands

Boston Scientific 6498, Patient Manual

Search results

Summary of Contents for 6498

Reviews:

Related manuals for 6498

Brands by name

Popular brands