Bosch WNA14400SG Instruction Manual And Installation Instructions Download Page 37

Page: 37 / 52

Operating the appliance

■

Observe the maximum specified

load. Overfilling adversely affects the

washing/drying result and promotes

creasing. Make sure that no items of

laundry are trapped between the

door and the rubber seal, and close

the door.

Dosing and adding detergent

and care products

Caution!

Damage to the appliance

Detergents and agents for the

pretreatment of laundry (e.g. stain

remover, prewash sprays, etc.) may

damage the surfaces of the appliance.

Keep these agents away from the

surfaces of the appliance. Using a

damp cloth, immediately remove any

fine spray residue and other residue/

droplets.

Dosing

Dose the detergents and care products

according to:

■

water hardness (ask your water

supply company),

■

the manufacturer’s specifications on

the packaging,

■

the amount of laundry,

■

soiling.

Filling the dispensers

Pull out the detergent drawer.

Warning

Eye / skin irritation!

If the detergent drawer is opened

while the appliance is running,

detergent/care product may run out.

Carefully open the drawer.

If detergent/care product comes into

contact with eyes or skin, rinse

thoroughly.

If accidentally swallowed, seek

medical advice.

Pour in detergent and/or cleaning

product.

Notes

■

Always follow the manufacturer's

instructions when dosing

all detergents, cleaning aids, care

products and cleaning agents.

■

Dilute viscous fabric softener

and fabric conditioner with water.

This will prevent blockages.

■

Be careful when opening the

detergent drawer while the appliance

is running.

Starting the programme

Touch and hold

Start/Reload

button for 1~2 seconds, then release

the button. The programme starts and

the appliance door is locked.
The finish-in time is shown in the display

panel and counts down until the

programme starts. After the programme

has started, the programme duration is

displayed. And the symbols for the

programme progress are lighting up.

Dispenser

Detergent for pretreat and

clothing disinfectant. (only for

the appliance with pretreat and

disinfectant function)

Dispenser

Softener, starch. Do not exceed

the maximum load.

Dispenser

Detergent for main wash, water

softener, bleach, stain remover.

Summary of Contents for WNA14400SG





















































Search results

Summary of Contents for WNA14400SG

Reviews:

Related manuals for WNA14400SG

Brands by name

Popular brands

Bosch WNA14400SG, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WNA14400SG

Reviews:

Related manuals for WNA14400SG

Brands by name

Popular brands