background image

Faults and what to do about them       

en

45

3

 Faults and what to do 

about them 

Faults and what to do about them

Emergency release

E.g. power outage or in the event of a 

loss of power
The programme continues when the 

power supply is restored.

However, if the laundry has to be 

removed, the appliance door can be 

opened as follows:

:

Warning

Risk of scalding!

When you are washing at high 

temperatures, there is a risk of scalding 

if you come into contact with hot water 

and laundry.

If possible, leave it to cool down first.

:

Warning

Risk of injury!

Reaching into the drum while it is still 

turning may cause hand injuries.

Do not reach into the drum when it is 

turning.

Wait until the drum has stopped turning.

Caution!

Water damage!

Any escaping water may cause water 

damage.

Do not open the door if water can be 

seen through the glass.

1.

Turn the programme selector to  

Off

Pull out the mains plug.

2.

Open the service flap.

3.

Drain the water. 

~

 Page 43

4.

Pull the emergency release 

downwards with a tool and release.

The door can then be opened.

Summary of Contents for WGG454A0ID





















































Reviews: