background image

en

    Appliance settings

54

Q

Appliance settings

Appliance settings

You can change the following appliance 

settings:

Settings that can be selected:

End signal

off – quiet – medium – loud – very 

loud

Adjust the volume of the end signal.

Button signal

off – quiet – medium – loud – very 

loud

Adjust the volume of the button 

signals.

Auto power-off of the appliance

in 15 – 30 – 60 min – never

The appliance automatically 

switches off after ... minutes 

(= 0 kWh energy consumption); to 

switch on, press the 

#

 main switch 

button.

Note:  

If you have Wi-Fi switched on, 

the automatic switch-off is set to 

Never

.

Language

Deutsch

English

...

Change the displayed language.

Info: Drum cleaning

on – off

This instruction reminds you to run a 

drum cleaning programme. 

Dispenser content:

 

i-DOS 

i

I

w

 Contents

Fabric softener - detergent

Select/change the dispenser 

content.

Basic dosage:

 

i-DOS 

i

I

w

 Basic

10 ml – 200 ml

Set the basic dosage in accordance 

with the recommendations of the 

detergent/fabric softener 

manufacturer.

Basic dosage: 

 

i-DOS 

w

 Basic

10 ml – 200 ml

Set the basic dosage in accordance 

with the recommendation of the 

detergent manufacturer.

To change the settings, press and hold 

both 

Basic settings 3 sec. 

buttons for 

approx. three seconds. 

~

 Page 26

Notes

The settings are retained after the 

appliance is switched off.

If you press and hold the buttons, 

the settings run through 

automatically.

Summary of Contents for WAY288H9GR





































































Reviews: