background image

Operating the appliance       

en

41

Select additional programme 

settings

By selecting additional settings/options, 

you can better adapt the washing 

process to your items of laundry.
The settings can be selected or 

deselected depending on the progress 

of the programme. 

~

 Page 25

The EcoPerfect 

F

 and SpeedPerfect 

(

 

button indicator lamps light up if a 

setting is activated.
The other settings are indicated by a 

symbol on the display panel if the 

setting is activated.
For multi-level settings, press and hold 

the buttons to run through the settings 

automatically.
The settings are not saved after the 

washing machine is switched off.
Additional programme settings/options 

~

 Page 37

Placing laundry into the drum

:

Warning

Risk of death!

Items of laundry pretreated with 

cleaning agents that contain solvents, 

e.g. stain remover/cleaning solvent, 

may cause an explosion after being 

loaded into the washing machine.

Hand-rinse these items of laundry 

thoroughly beforehand.

Load the pre-sorted, unfolded laundry 

into the drum. The load screen for the 

selected programme (e.g. 

Easy-care

) is 

indicated on the display panel. 

The load bar fills as the laundry is 

loaded. If the maximum load is 

exceeded, the bar flashes. Observe the 

maximum indicated load. Overfilling 

adversely affects the washing result and 

encourages creasing.

Notes

Mix items of laundry of varying sizes. 

Laundry items of different sizes 

distribute themselves better during 

the spin cycle. Individual laundry 

items may cause an unbalanced 

load. 

Wait until the Bosch logo no longer 

appears before adding laundry.

The load screen appears when the 

door is opened or when the amount 

of laundry is changed.

3OHDVHORDGODXQGU\PD[NJ

'RVDJHDXWRPDWLF

öüü

Summary of Contents for WAY288H9GR





































































Reviews: