background image

Intelligent dosing system       

en

45

When the appliance is switched on, the 

fact that the detergent drawer is closed 

completely is indicated by the following:

If intelligent dosagei-DOS 

w

 or 

i-DOS 

i

 has been selected, the 

corresponding indicator lights up.

If intelligent dosage has not been 

selected, the indicator flashes once 

and then goes out.

The 

ù

 symbol in the display panel 

goes out.

Everyday use

Indicator lights in the display panel:

The display 

lights up

 if intelligent 

dosage has been selected for the 

dispenser. 

The display 

flashes

 if the fill level of 

the selected intelligent dosing 

dispenser is below the minimum 

level.

(De)selecting intelligent dosage and 

adjusting the dosage strength:

The intelligent dosages for detergent 

and fabric softener are set at the factory 

for programmes in which intelligent 

dosage can be used. 
Overview of programmes 

~

 Page 31

The dosage strength has been preset to 

low (lightly soiled laundry) for 

detergent 

w

 and to medium (medium 

level of softness) for fabric softener 

i

. It 

can be changed for each programme. 

~

 Page 38

In addition to intelligent dosage, 

cleaning aids (e.g. stain remover) can 

be added manually to compartment 

v

 

u

, if necessary. 

~

 Page 47

Note:  

The selection (on/off) and the 

selected dosage strength for i-DOS 

i

 

and i-DOS 

w

 are saved for each 

programme until they are changed 

again, even if the washing machine is 

switched off.

Topping up the detergent/ fabric 

softener:

If the indicator light for the selected 

intelligent dosage flashes, this means 

that the amount of detergent or fabric 

softener in the dispenser is below the 

minimum fill level. The contents will last 

for another three washes or so. 
The same detergent or fabric softener 

can be added at any time. If you change 

product/manufacturer, we recommend 

that you clean the dispensers first. 

~

 Page 56

If required, adjust the basic dosage.

Basic settings

The basic dosages are:

For detergents

 – based on the 

manufacturer’s recommendation for 

average soiling and the respective 

water hardness.

F or fabric softeners

 – based on the 

manufacturer's recommendation for 

a medium level of softness.

Refer to the packaging label on your 

detergent/fabric softener or ask the 

manufacturer directly for this 

information.
To find out the hardness of your water 

supply, use a test strip or check with 

your water supplier.

Summary of Contents for WAWH26I9SN





































































Reviews: