Bosch WAW28640AU Instruction Manual And Installation Instructions Download

Page: 62 / 64

Technical data

Information for test institute

Items

Instruction

Pre-treatment of new

appliance

Run two empty runs of Cottons 90 °C with 1400 rpm: The

1st run with 50g detergent and 8g anti sudsing agent, the

2nd run without detergent and sudsing agent.

According to standard

AS NZS 2040.1-2005

AS NZS 2040.2-2005

AS NZ 6400-2016

Washing programme

Cottons 60°C + EcoPerfect + Rinse Plus, 9 kg, 1400 rpm

Testing instructions

The dosage of detergent: 12,5g/kg

The dosage of anti sudsing agent: 2g/kg

Add the dry powder detergent into main wash dispenser

before start. After detergent is flushed in add the PBIS

solution and anti-sudsing agent as soon as possible.

Age of test loads

The average age of test load around 10~20 times is

recommended to replicate normal use.

Loading Procedure

The items are loaded into the drum by circle first, then by

layers according to the table and picture below evenly.

No. of Layers

Items of garments

External circle

sheets, bath towels

Layer1

Tablecloth

Layer2

Shirts, T-shirts, Pillow cases

Layer3

Shorts (all), Wash cloths (all),handkerchiefs (all)

Layer4

Shirts, T-shirts, Pillow cases

Layer5

Tablecloth

([WHUQDOFLUFOH

/D\HU

'UXP

/D\HU

Summary of Contents for WAW28640AU

































































Search results

Summary of Contents for WAW28640AU

Reviews:

Related manuals for WAW28640AU

Brands by name

Popular brands

Bosch WAW28640AU, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WAW28640AU

Reviews:

Related manuals for WAW28640AU

Brands by name

Popular brands