background image

en

        Faults and what to do about them.

40

3

 Faults and what to do 

about them. 

Faults and what to do about them.

Emergency release

E.g. in the event of a power cut
The programme continues when the 

power supply is restored. 

However, if the laundry has to be 

removed, the washing machine door 

can be opened as follows:

:

Warning

Risk of scalding!

When you are washing at high 

temperatures, there is a risk of scalding 

if you come into contact with hot 

detergent solution and laundry. 

If possible, leave it to cool down first.

:

Warning

Risk of injury!

Reaching into the drum while it is still 

turning may cause hand injuries.

Do not reach into the drum when it is 

turning. 

Wait until the drum has stopped turning.

:

Warning

Irritation of the respiratory tract!

Any active oxygen that is emitted may 

irritate the mucosa and cause eyes to 

water.

Do not open the door using the 

emergency release if a programme is 

running with active oxygen.

Wait until there is no active oxygen in 

the drum.

Caution!

Water damage

Any escaping water may cause water 

damage.

Do not open the washing machine door 

if water can be seen through the glass.

1.

Switch off the appliance. Pull out the 

mains plug.

2.

Drain the water

~

 Page 38

3.

Use a tool to pull the emergency 

release downwards and then 

release.

The washing machine door can then 

be opened.

Information on the display panel

Indicator

Cause/remedy

è

 off

The door is unlocked at the end of the programme or when paused, laundry can be 

added/removed

è

 is lit up

During the programme. Door locked.

Paused: Temperature too high. Wait until the temperature drops.

Paused: Spin speed too high. Wait until the drum comes to a halt.

Paused: Water level too high. It is not possible to add laundry. Touch 

A

 to 

continue the programme.

Summary of Contents for WAT2876XES

















































Reviews: