background image

Safety instructions    

en

5

(

Safety instructions

Safety instructions

Electrical safety

:

Warning

Danger of death!

There is a risk of electric shock 

if you touch live components.

Never touch or hold the 

mains plug with wet hands.

Only pull out the mains cable 

by the plug and never by the 

cable, as this could damage 

it.

The appliance must be 

grounded. 

Electrical connection 

~

 Page 36

Risk of injury

:

Warning

Risk of injury!

When the washing machine 

is lifted by its protruding 

parts (e.g. the washing 

machine door), the 

components may break off 

and cause injuries. 

Do not lift the washing 

machine by protruding parts.

If you climb on the washing 

machine, the worktop may 

break and cause injuries.

Do not climb onto the 

washing machine.

If you lean on the washing 

machine door when it is 

open, the washing machine 

may tip over and cause 

injuries.

Do not lean on the washing 

machine door when it is 

open.

Reaching into the drum 

when it is turning can cause 

injuries to hands.

Do not reach into the drum 

when it is turning. 

Wait until the drum has 

stopped turning.

:

Warning

Risk of scalding!

When you are washing at high 

temperatures, there is a risk of 

scalding if you come into 

contact with hot water e.g. if hot 

water is being drained into a 

wash basin. 

Do not reach into the hot 

detergent solution.

Safety for children

:

Warning

Danger of death!

If children play with the washing 

machine, they may get into life-

threatening situations or injure 

themselves.

Do not leave children 

unattended near the washing 

machine.

Do not let children play with 

the washing machine.

Summary of Contents for WAK20260IN









































Reviews: