Bosch VideoJet 8004 Installation And Operating Manual Download Page 15

Page: 15 / 164

VideoJet 8008 / VideoJet 8004

| Installation and Operating Manual

| 15

Bosch Security Systems | 2006-07 | V1.5

Product description

Front panel

10 Power

LED

lights up green when ready for operation

11 IR

diode

infrared receiver (for future function extensions)

12 HDD

LED

flashes red during data transmission to and from the hard drive

13 Fail

LED

flashes red during hardware error (defective fans)

Display
for displaying operating parameters

15 Menu/Exit

key

for activating and deactivating the configuration menu

16 Set

key

for saving changes to the operating parameters
(for future function extensions)

Arrow keys
for navigation in the display menu

For more information about the LEDs, see page 143.

Summary of Contents for VideoJet 8004





































































































































































Search results

Summary of Contents for VideoJet 8004

Reviews:

Bosch VideoJet 8004, Installation And Operating Manual, Page: 15 / 164

Search results

Summary of Contents for VideoJet 8004

Reviews: