Bosch SPU6ZMS10S User Manual Download Page 6

Page: 6 / 60

Safety

WARNING ‒ Risk of fire!

It is dangerous to use an extended power cord and non-ap-
proved adapters.

▶

Do not use extension cables or multiple socket strips.

▶

If the power cord is too short, contact Customer Service.

▶

Only use adapters approved by the manufacturer.

WARNING ‒ Risk of injury!

Hinges move when opening and closing the appliance door
and can cause injury.

▶

If built-under or integrable appliances are not in a cavity so
that one side is accessible, the hinge area must be covered
at the side. Covers are available from Customer Service or
specialist outlets.

WARNING ‒ Risk of tipping!

Improper installation may cause the appliance to tip up.

▶

Only install built-under or integrable appliances under a
continuous worktop that is securely connected to adjacent
cabinets.

Safe use

Follow these safety instructions when using the appliance.

WARNING ‒ Risk of serious harm to health!

Failure to comply with safety instructions and directions for
use on packagings of detergent and rinse aid products may
cause serious harm to health.

▶

Follow the safety instructions and directions for use on the
packagings of detergent and rinse aid products.

WARNING ‒ Risk of explosion!

Adding solvents to the interior of the appliance may cause ex-
plosions.

▶

Never add solvents to the interior of the appliance.

Summary of Contents for SPU6ZMS10S





























































Search results

Summary of Contents for SPU6ZMS10S

Reviews:

Related manuals for SPU6ZMS10S

Brands by name

Popular brands

Bosch SPU6ZMS10S, User Manual

Search results

Summary of Contents for SPU6ZMS10S

Reviews:

Related manuals for SPU6ZMS10S

Brands by name

Popular brands