Bosch SHP65TL5UC Repair Instructions Download

Page: 65 / 82

702_58300000170749_ara_en_c

Page 65 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

FAULT DIAGNOSTICS

6.1

Error codes (service / customer)

6.1.1

Entering the error code program

•

If the dishwasher needs to be reset, turn it on and off

again. The dishwasher must be off to enter the program.

•

While pressing and holding both the “

” and “

” buttons

(below)

, press and hold the

On / Off

button (to turn the

dishwasher on) until the display shows “

”. Release all

buttons.

•

Program “

” is the error code program.

6.1.2

Viewing error code displays

•

Press the “

” button

(below)

to start the error code

program.

•

The program shows

both

the storage location of the error

code (“

C:00

–

C:07

”) and the error codes themselves

(“

E:00

–

E:30

To view storage locations, press and hold the “

”

button.

To view error codes, release the “

” button.

6.1.3

Exiting the error code program

•

Turn the dishwasher off to exit the program.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands