Bosch SHP65TL5UC Repair Instructions Download

Page: 64 / 82

702_58300000170749_ara_en_c

Page 64 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

2. Move rack slide cutouts away from tank wheels.

5.21 Time Light (selected models)

Tools needed: T20 Torx & #2 Phillips screwdrivers and pliers

Remove outer door

– section 5.1.2.1.

Remove toe kick

– section 5.1.4.2. Pull dishwasher out

enough to clear hinges.

Remove base cover

– section 5.1.4.3. This eliminates

disconnecting and reconnecting all wire harnesses.

4. Disconnect harness from Time Light

(below left)

5. Slide Time Light projector up from base cover, rotating it

slightly ccw (counterclockwise) as you go

(below right)

5.22 Emotion Light (selected models)

Tools needed: T20 Torx & #2 Phillips screwdrivers and pliers

Disconnect & pull out dishwasher

– section 5.1.5.1.

2. Open LED covers.

3. Carefully remove both LEDs with covers from the tank.

4. Carefully peel back the ribbon cable and disconnect the

wire harness from it.

CAUTION:

Take care to not damage the delicate ribbon

cable.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands