Bosch SHP65TL5UC Repair Instructions Download

Page: 51 / 82

702_58300000170749_ara_en_c

Page 51 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4. Slide water valve up and out of mounting bracket. When

installing new water valve, slide valve flange over bracket
sides and snap valve into bracket

(below)

5. Loosen hose clamp and disconnect water inlet hose from

rear of valve.

6. Disconnect wire harness from water valve

(below)

7. Unscrew supply hose from water valve.

8. Remove any water from sump & base.

CONNECTION HINTS:



Water connection 3/8” NPT female. Inlet water pressure

range 5 - 120 psi (0.3 – 8.27 bars).



When reconnecting the water supply to the water valve,

don’t overtighten the elbow fitting. Hand tighten snugly.



not

use Teflon tape on water fittings as it can keep

hose seals from seating properly to prevent leaking.

5.6

Drain pump

Access the drain pump from the front of the dishwasher base by
removing the base cover.

Tools needed: T20 Torx & #2 Phillips screwdrivers and pliers

Remove parts for bottom front access

– section 5.1.4.1.

2. Disconnect wire harness from drain pump

(below)

3. Remove the drain pump by lifting the latch, rotating the

pump clockwise and pulling the pump out

(below)

5.7

Aqua sensor

Access the aqua sensor from the front of the dishwasher base by
removing the base cover.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands