Bosch SHP65TL5UC Repair Instructions Download

Page: 47 / 82

702_58300000170749_ara_en_c

Page 47 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

6. Disconnect top / side wire harnesses from power module

(below)

, making sure to remove the harnesses with their

caps, not individually.

TIP:

Check error codes

before

replacing power

modules. Many good power modules are replaced and
faulty parts aren’t replaced, causing repeat calls.

Not all terminals are used. To protect power modules, two
plugs are used to cover unused terminals.

5.3

Dispenser

Although many dispenser components can be replaced, it’s
quicker to replace the entire dispenser.

5.3.1

To remove dispensers

Dispensers are easily removed from inner doors by removing
outer doors.

Tools needed: T20 Torx, flat blade screwdrivers & gloves

Remove outer door

– section 5.1.2.1.

2. Disconnect wire harnesses from dispenser after noting

connector locations

(below left)

3. Remove cable guide

(below right).

CAUTION

– 80% of all controls returned

for analysis check out OK. Most control
issues are due to loose connections and
error codes for other parts.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands