Bosch SHP65TL5UC Repair Instructions Download | Manualshive

Page: 34 / 82

background image

702_58300000170749_ara_en_c

Page 34 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4.20 Operation

4.20.1

Water spray system

The spray system consists of 3 spraying levels: lower /  upper
spray arms and a top sprinkler.    Water is supplied to the upper
spray arm and the top sprinkler by the fill tube at the rear of the
tank.

The fill tube has 2 separate water channels so the upper spray
arm and top sprinkler can be operated separately.

The upper spray arm is attached by its feed tube directly to the
upper rack. The feed tube has an adjustable coupling to allow it
to move up and down as the upper rack is raised or lowered.

The lower spray arm is connected by directly to the sump. It has
a nozzle underneath it to clean the sump filters and to rinse food
debris into them.

1

2

3

4

5

6

7

8

1.  Top sprinkler
2.  Upper spray arm coupling
3.  Feed tube
4.  Water switch

5.  Heat pump
6.  Sump
7.  Lower spray arm
8.  Upper spray arm

«
...
32
33
34
35
36
...
»

Summary of Contents for SHP65TL5UC



















































































Reviews:

No comments

Related manuals for SHP65TL5UC

Brand: DAEWOO ELECTRONICS Pages: 28

Brand: Alliance Laundry Systems Pages: 38

ODW 60032 FS A2

Brand: OK. Pages: 27

Brand: GE Pages: 52

BI WDIL 75125 UK N

Brand: Indesit Pages: 4

Brand: Tesla Pages: 242

Brand: Ardo Pages: 52

Brand: Fisher & Paykel Pages: 6

Brand: Haier Pages: 20

Brand: Samsung Pages: 48

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 23

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 23

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands