Bosch SHP65TL5UC Repair Instructions Download | Manualshive

Page: 33 / 82

background image

702_58300000170749_ara_en_c

Page 33 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4.19 Emotion light (selected models)

The

Emotion Light

, located at the top of the dishwasher above

the cutlery drawer, lights up the inside of the dishwasher. It’s

blue

or white light provides a soothing glow.

It comes on whenever the door is open whether the dishwasher is
on or not. The light is off when the door is closed and will turn off
whenever the door has been left open for 60 minutes or more.

1.  LED’s
2.  Ribbon cable
3.  Covers

Rating: 13.5 VDC

1

1

2

3

3

«
...
31
32
33
34
35
...
»

Summary of Contents for SHP65TL5UC



















































































Reviews:

No comments

Related manuals for SHP65TL5UC

Brand: VESTEL Pages: 16

Sicily Glory G01

Brand: Midea Pages: 65

Brand: Jet-tech Pages: 10

Brand: Magic Chef Pages: 12

Brand: Campomatic Pages: 36

Brand: Sammic Pages: 28

Brand: Gaggenau Pages: 52

Brand: Dawlance Pages: 4

Brand: Asko Pages: 2

Brand: General Technomatic Pages: 10

Brand: Hoover Pages: 33

Brand: Asko Pages: 32

Brand: Samsung Pages: 44

Brand: Samsung Pages: 24

Brand: Samsung Pages: 96

WA25B8377 Series

Brand: Samsung Pages: 168

Brand: Samsung Pages: 118

Brand: Electrolux Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands