Bosch SHP65TL5UC Repair Instructions Download

Page: 29 / 82

702_58300000170749_ara_en_c

Page 29 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4.14.3

Backflow valve

The backflow valve is located inside the sump at the outlet to the
drain hose. It prevents waste water from entering the sump.

4.15 Sump filters

The sump contains several types of filters: a filter screen, coarse
filter and micro filter.

5.  Coarse filter
6.  Microfilter
7.  Filter screen

4.16 Tank with base and sump

4.16.1

Base

The plastic assembly is cast into one piece and contains
mounting provisions for all parts mounted to it.

4.16.2

Tank

The ss tank isn’t available as a service part. The top, bottom and
sides are made from 304 ss alloy and the back is made from 430
ss alloy.

1. Backflow valve assembly
2. Flap

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands