Bosch SHP65TL5UC Repair Instructions Download | Manualshive

Page: 19 / 82

background image

702_58300000170749_ara_en_c

Page 19 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

During each wash program, the dispenser operates twice, once
to dispense detergent and again to dispense rinse-aid.

1.  Coil
2.  Actuator
3.  Rinse-aid pump
4.  Optical rinse-aid sensor
5.  Cover release lever

The coil

(1)

,

powered by 165

VDC pulses from the control,
moves the detergent cover
actuator

(2)

to the left. A plastic

link turns, rotating the detergent
cover release lever

(5)

, which

opens the detergent cover.

A mechanical link between the coil actuator and rinse-aid valve
prevents rinse aid from being dispensed when the coil is 1

st

actuated. After the detergent cover has opened, the link moves
and latches in place, allowing the rinse-aid pump to dispense
rinse aid.

Each 165 VDC control pulse dispenses 1 ml of rinse aid – the
total amount depends on the dispenser setting. A vent equalizes
internal pressure to dispense rinse-aid accurately.

The actuator is “reset” when the detergent door is opened so the
detergent cover opens first the next time the coil is activated.

Detergent tablets dissolve more slowly if there’s moisture left in
the detergent dispenser. Two plastic ribs in the detergent cup
prevent detergent tablets from “sticking” to the cup.

CAUTION:

Inner door edges are sharp! Cover inner door

edges and remove dispenser carefully.

4.4

Heat pump

4.4.1

Heat pump basics

The heat pump contains the heating element, motor speed
sensor, two temperature sensors (NTC’s), motor and pump
(head). The component parts aren’t available separately.

There’s no flow-through heater, flow switch or Hi-Limit cutout  –
the  heat  pump  uses  a flow-through heated  cylinder.    The  120
VAC, 1200W heater cylinder provides more heating surface area
and heats water faster (~ 2ºF / minute).

The pump impeller is driven by a 3-pole BLDC motor controlled
by the power module.

1.  Pump suspension strap
2.  Heating element
3.  Seal ring

1

2

3

1

2

1 2

3

4

3

5

«
...
17
18
19
20
21
...
»

Summary of Contents for SHP65TL5UC



















































































Reviews:

No comments

Related manuals for SHP65TL5UC

Brand: GE Pages: 11

Brand: Dacor Pages: 16

Brand: Samsung Pages: 16

Brand: Alliance Laundry Systems Pages: 32

Brand: NEFF Pages: 30

Brand: DELLA Pages: 7

Brand: Smeg Pages: 26

Dishwasher DWD63.1SS

Brand: Smeg Pages: 15

Brand: Maytag Pages: 36

Brand: ZANKER Pages: 17

Brand: Samsung Pages: 80

Brand: Samsung Pages: 136

Brand: Samsung Pages: 210

Brand: Samsung Pages: 234

WA52M7755A series

Brand: Samsung Pages: 236

WA55CG71 A Series

Brand: Samsung Pages: 72

Brand: Samsung Pages: 104

Brand: Samsung Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands