Bosch SHP65TL5UC Repair Instructions Download

Page: 14 / 82

702_58300000170749_ara_en_c

Page 14 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

3.6

Dishwasher set up

Many dishwasher settings can be changed on the fascia panel
and will be stored in memory until changed again.

3.6.1

Explaining settings

3.6.1.1 Auto Power Off

To save energy, the

Auto Power Off

feature turns the dishwasher

off 1 minute after the wash cycle ends. It can be turned off or
changed to turning off the dishwasher two (2) hours after the
cycle ends.

3.6.1.2 Info Light (selected models)

red

blue

light

(LED)

, depending on the model, shines on the

floor to indicate the dishwasher is running. The door shouldn’t be
opened until the light has gone out.

3.6.2

To enter mode to change settings

Press the

On / Off

button to turn the dishwasher on. While

pressing and holding the “

” button

(below)

, press and hold the

Start

button until the display shows “

d:00

”. Release both buttons.

3.6.3

To select and change settings

To select the setting to be changed, press button “

” to scroll

through possible selections

(see chart below)

. To change the

value of the chosen setting, press button “

” repeatedly until the

desired value is chosen.

Setting

Value

Description

Hot water
connection

A:00 – A:01

off

Factory setting:

A:00 = Off

Water
hardness

H:00 – H:07 8 ranges

Factory setting:

H:04

Extra Dry

d:00 – d:01

off

Factory setting:

d:00 = Off

Rinse-aid

r:00 – r:06

6 ranges &

none

Factory setting:

r:05

End of Cycle
Tone

b:00 – b:03

3 ranges &

off

Factory setting:

b:02

Language

L:01 – L:23

23 languages
Factory setting:

L:01 = German

Auto Power
Off

P:00 – P-02

P:00

–

Dishwasher doesn’t turn

off automatically

P:01

–

Dishwasher turns off

after 1 minute

P:02

–

Dishwasher turns off

after 2 hours

Factory setting:

P:01

Emotion Light

(selected models)

E:00 – E:01

off

Factory setting:

E:01 = On

Time Light

(selected models)

S:00 – S:01

off

Factory setting:

S:01 = On

Info Light

(selected models)

I:00 – I:01

off

Factory setting:

I:01 = On

3.6.4

To exit and save settings

Press the

Start

button.

Summary of Contents for SHP65TL5UC



















































































Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands

Bosch SHP65TL5UC, Repair Instructions

Search results

Summary of Contents for SHP65TL5UC

Reviews:

Related manuals for SHP65TL5UC

Brands by name

Popular brands